DeWalt DW734 Manual De Instrucciones página 8

Cepillo portátil de 318 mm (12-1/2") para trabajo pesado
Ocultar thumbs Ver también para DW734:
Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

FIG. 22
P
FIG. 23
FIG. 24
Q
FIG. 25
R
FIG. 26
S
T
FIG. 27
FIG. 28
U
V
should contact the edge of the table extension and the main
table (Fig. 7). When leveling, press the edge of the table
extensions down to remove any play. For best results, use a
level long enough to contact the edges of both table exten-
sions.
If the table extensions are not level, loosen the jam nuts (T)
and adjust the table extension support bolts (S) up or down
(Fig. 26).
NOTE: The outside edges of the extension tables are level
with the base while the inside edges (closest to the cutter
head) are below the edge of the base. This is set at the fac-
tory to reduce unnecessary friction between the material and
the table while providing adequate support at the two points
(those farthest from the cutter head) on the tables that are
integral to snipe prevention.
TABLE
Keep the table clean and free from oil, grease and pitch. Treat
the table with paste wax to help maintain its smooth finish.
Circuit Breaker Reset Button
(Fig. 27)
Your planer is equipped with an 18 amp circuit breaker. If
your planer becomes overloaded and stops operating, turn
off the planer, let the unit sit for 2 minutes and press the reset
button (U) before you resume working.
WARNING: To prevent the planer from starting unexpect-
edly if power is interrupted by a circuit breaker trip, make sure
the switch is in the OFF position before restoring power.
NOTE: Circuit breaker overload is often the result of dull
knives. Change your knives on a regular basis to avoid trip-
ping your breaker. Check your knives before re-setting the
circuit breaker and continuing to plane.
See the Troubleshooting Guide at the end of this section for
more information.
Brushes
Inspect carbon brushes regularly. Keep brushes clean and
sliding freely in their guides. Always replace a used brush in
the same orientation in the holder as it was prior to its
removal.
Carbon brushes have varying symbols stamped into their
sides, and if the brushes are worn down to the line closest to
6
the spring, they must be replaced. Use only identical
D
WALT brushes.
E
New brush assemblies are available at D
centers. After replacing brush assemblies, the tool should be
allowed to "run in" (run at no load) for 10 minutes to seat new
brushes before using.
TO REMOVE BRUSH ASSEMBLY (FIG. 28)
WARNING: DISCONNECT TOOL FROM THE POWER
SOURCE BEFORE ATTEMPTING TO REMOVE BRUSH
ASSEMBLY.
1. Remove the brush inspection cap (V).
2. Withdraw the brush assembly.
Cleaning and Lubrication
CAUTION: Never let any liquid get inside the tool; never
immerse any part of the tool into a liquid. Electric shock may
result.
CAUTION: Never use solvents or other harsh chemicals
for cleaning the non-metallic parts of the tool.
It is recommended that, once a year, you take or send the
tool to a D
WALT certified service center for a thorough
E
cleaning, inspection and lubrication of the gear case.
Accessories
There are three accessories available for the DW734 thick-
ness planer:
• DW7331 – Dust Hood for DW734 (also fits the DW733)
• DW7342 – 12-1/2" Disposable Reversible Planer Knives
• DW7350 – Mobile Stand
CAUTION: The use of any other accessory not recom-
mended for use with this tool could be hazardous.
If you need any assistance in locating these accessories,
please contact D
WALT Industrial Tool Co., 701 East
E
Joppa Road, Baltimore, MD 21286 or call 1-800-4-D
(1-800-433-9258).
Repairs
To assure product SAFETY and RELIABILITY, repairs, main-
tenance and adjustment should be performed by authorized
service centers or other qualified service personnel. Always
use identical replacement parts.
Three Year Limited Warranty
D
WALT will repair, without charge, any defects due to faulty
E
materials or workmanship for three years from the date of
purchase. This warranty does not cover part failure due to
normal wear or tool abuse. For further detail of warranty cov-
erage and warranty repair information, visit www.dewalt.com
or call 1-800-4-D
WALT (1-800-433-9258). This warranty
E
does not apply to accessories or damage caused where
repairs have been made or attempted by others. This war-
ranty gives you specific legal rights and you may have other
rights which vary in certain states or provinces.
In addition to the warranty, D
WALT tools are covered by our:
E
1 YEAR FREE SERVICE
D
WALT will maintain the tool and replace worn parts
E
caused by normal use, for free, any time during the first year
after purchase.
WALT service
E
WALT
E

Publicidad

Tabla de contenido
loading

Tabla de contenido