Virutex TM43L Manual De Instrucciones página 8

Swivel Table:
Swivels right and left up to 45°, with fixturing at
0° - 15° - 22.5° - 30° and 45°.
Tilting Head:
Tilts between 90° and 45° to the base with the table
in any position from 0° to 45° to the left.
Weight........................................................18 kg
Packaging dimensions............670x610x430 mm
Weighted equivalent continuous
acoustic pressure level A.......................97 dBA
Acoustic power level A....................................108 dBA
Uncertainty........................................................K = 3 dbA
Wear ear protection!
Vibration total values.................................a
Uncertainty......................................................K: 1.5 m/s
2. MAXIMUM CUTTING CAPACITIES
- at 0° x 0° (Fig. 1)...............................145 x 62 mm
- at 0° x 45° (Fig. 2).............................145 x 45 mm
- at 45° x 0° (Fig. 3)...............................62 x 95 mm
- at 45° x 45° (Fig. 4).............................43 x 45 mm
- on the upper table (*)................................40 mm
(*) Only on model TM43L
3. SAFETY MECHANISMS
3.1 SWITCH
The machine has a swith a blocking button located
on the handle, so that when pressure on the swith
is released, the energy supply is interrupted and the
machine stops automatically.
By blocking the side button of the switch, we can
use the machine for mitering on the upper table in
(TM43L) models.
For your safety, never use the switch in
the blocked position for mitering work.
3.2 BLADE GUARDS
At rest, the sawblade is completely covered by the
guards and the machine is blocked in this position. Le-
ver A (Fig. 5) unblocks the assembly prior to lowering.
Make sure that the sawblade is com-
pletely covered by the guards when
the machine is at rest. See that these
blade guards are always kept in good
condition.
8
3.3 PROTECTION AGAINST ACCIDENTAL
START-UP DUE TO POWER CUTS
This machine is fitted with a device which, in the case
of a drop in voltage or a power cut, breaks the circuit
and prevents accidental start-up when the current
returns, even if the switch-locking button is actuated.
To restart the machine, unlock the push-button
switch and then just press it normally.
3.4 PROTECTION AGAINST SHORT CIRCUITS
The machine's circuit includes a T1 fuse (Fig. 10), which
protects it from short-circuiting and overloading.
The fuse is located in the junction box. Should it have
to be replaced, unscrew the lid of the fuse box and
remove the burnt-out fuse. Replace it with another
: 2.5 m/s
2
h
one of the same type (5 X 20 8 A, type T).
2
4. UNPACKAGING THE MACHINE
Inside the box you will find the following items:
- Tiltable mitre saw as per model (TM43L or TS48L)
- Set of Allen keys, ccs 8 mm
- Allen key, ccs 5 mm
- Timber stop assy.
- Pushing accessory for cutting on the upper bench
(only TM43L)
- Instructions manual and parts lists
- General safety instructions leaflet
- Leaflets various
For transportation purposes, the machine head is
locked in its lower position. To unpack it, simply take
it by the handle and remove it from thebox.
5. PREPARATION AND SETTING UP
5.1 INSTALLATION
To use the machine in a fixed place, we suggest bolting
it to a work bench or table about 90 cm high, using
the B holes made in the base (Fig. 7). We recommend
our accessory PORTABLE WORKTABLE MT58K (Ref.
5800100) (Fig. 24)
This machine is designed only for indoor work and
must not therefore be exposed to rain or damp
surroundings.
5.2 HANDLE
Make sure the appliance is disconnected
from the mains supply before undertaking
any preparation or maintenance work on it.