Specifications - Sony Trinition PVM-20S1WE Manual De Instrucciones

Specifications

Video signal
Color system NTSC, PAL, SECAM, NTSC
Resolution 300 TV lines
Aperture correction 0 dB to +6 dB
Frequency response
LINE 6 MHz ±3 dB (Y signal)
RGB 6 MHz ±3 dB
Synchronization AFC time constant 1.0 msec.
Picture performance
Normal scan 7 % over scan of CRT effective screen
area
Under scan 5 % underscan of CRT effective screen
area
H. linearity Less than 8.0 % (typical)
V. linearity Less than 7.0 % (typical)
Convergence
Central area: 0.6 mm (typical)
Peripheral area: 1.2 mm (typical)
Raster size stability H: 1.0 %, V: 1.5 %
High voltage regulation
4.0 %
Color temperature D65/D93, selectable
USER (3,200K–10,000K, factory
setting is D65)
Inputs
LINE A/B
VIDEO IN BNC connector (×2), 1Vp-p, ±6 dB,
sync negative
AUDIO IN Phono jack (×2), –5 dBu
47 kilo-ohms
LINE C
Y/C IN 4-pin mini-DIN (×1)
See the pin assignment on page 17.
AUDIO IN Phono jack (×1), –5 dBu
47 kilo-ohms
RGB/COMPONENT
R/R-Y, G/Y, B/B-Y IN: BNC connector (×3)
R, G, B channels: 0.7 Vp-p, ±6 dB
Sync on green: 0.3 Vp-p, negative
R-Y, B-Y channels: 0.7 Vp-p, ±6 dB
Y channel: 0.7 Vp-p, ±6 dB
(Standard color bar signal of 75 %
chrominance)
AUDIO IN Phono jack (×1), –5 dBu
47 kilo-ohms
EXT SYNC IN BNC connector (×1)
4 Vp-p, ±6 dB, sync negative
REMOTE 20-pin connector (×1)
See the pin assignment on page 17.
a) 0 dBu = 0.775 Vr.m.s.
16
Outputs
LINE A/B
4.43
VIDEO OUT
AUDIO OUT
LINE C
Y/C OUT
AUDIO OUT
RGB/COMPONENT
R/R-Y, G/Y, B/B-Y OUT: BNC connector (×3),
AUDIO OUT
EXT SYNC OUT
Speaker output
General
CRT
Power consumption 100 Wh (with SDI: 110 Wh)
Power requirements 220 to 240 V AC, 50/60Hz, 0.6 to 0.5 A
Peak inrush current
(1) Power ON, current probe method: 18 A (240 V)
(2) Hot switching inrush current, measured in
Operating temperature
Transport and Storage temperature
a)
, more than
Pressure
Humidity
Dimensions (w/h/d) Approx. 482 × 397 × 503 mm
a)
, more than
Mass
Accessory supplied AC power cord (1)
a)
, more than
Design and specifications are subject to change
without notice.
BNC connector (×2), loop-through
Automatic 75-ohm termination
Phono jack (×2), loop-through
4-pin mini-DIN (×1), loop-through
Automatic 75-ohm termination
Phono jack (×1), loop-through
loop-through
Automatic 75-ohm termination
Phono jack (×1), loop-through
BNC connector (×1), loop through
Automatic 75-ohm termination
Output level: 0.8 W
P-22 phosphor
100 to 120 V AC, 50/60Hz, 1.3 to 1.1 A
accordance with European standard EN55103-1:
7 A (230 V)
0 to +35°C (32 to 95°F)
–10 to +40°C (14 to104°F)
700 to 1,060 hPa
0 to 90% (no condensation)
(19 × 15 × 19
3 7
⁄ ⁄
4 8
not incl. projecting parts and controls
Approx. 25 kg (55 lb 2 oz)
AC plug holder (1)
Tally label (1)
Cable with a 20-pin connector (1)
Rack mount kit (1)
Rack mount brackets (A-type) (2)
Rack mount bracket (B-type:right)
(1)
Rack mount bracket (B-type:left)
(1)
Screws (B4 × 12) (4)
Operating instructions (1)
inches)