Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
Enlaces rápidos
Installation
Instructions
Unitized
Electric
Washer/Dryer
Questions
on installation?
Call: 1-800-GECARES {US} or Visit our Web site at: www.GEAppliances.com
(US).
In Canada, call 800.561.3344
or visit www.GEAppliances.cu
i
BEFORE YOU BEGIN
Readthese instructions completely and
carefully.
• IMPORTANT- save
these instructions for
local inspector's use.
•
IMPORTANT-
Observe all governing codes
and ordinances.
• Note to Installer - Be sure to leave these
instructions with the customer.
Note to Customer- Keepthese instructions with
your Owner's Hanual for future reference.
• Beforethe appliance is removed from service or
discarded,remove the washer and dryer doors.
Inspect the dryer exhaust outlet and straighten
the outlet walls if they are bent.
Service information and the wiring diagram are
located at the access panel.
Do not allow children on or in the appliance.
Closesupervision of children is necessary when
the appliance is used near children.
Install the appliance where the temperature is
above 50°F for satisfactory operation of the
control system.
• Productfailure due to improper installation is not
covered under the Warranty.
_LW_KI_I|I_I£_"
RISK OF FIRE
. To reduce the risk of severe injury or death, follow all installation
instructions.
Appliance installation must be performed by a qualified installer.
Install the appliance according to these instructions and in accordance
with local codes.
This appliance must be exhausted to the outdoors.
Use only 4" rigid metal ducting for exhausting the clothes dryer to the
outdoors.
DO NOT install a clothes dryer with flexible plastic ducting materials.
If flexible metal (semi-rigid or foil-type) duct is installed, it must be
UL listed and installed in accordance with the instructions found
in "Connecting The Dryer To House Vent" on page 8 of this manual.
Flexible venting materials are known to collapse, be easily crushed,
and trap lint. These conditions will obstruct dryer airflow and increase
the risk of fire.
Do not install or store this appliance in any location where it could be
exposed to water and or weather.
Save these instructions. (Installers: Be sure to leave these instructions
with the customer).
NOTE: installation
and service of this appliance
requires
basic
mechanical
and electrical
skills,
it is your
responsibility
to
contact
a qualified
installer
to make the electrical
connections.
TOOLS YOU WILL NEED
Slip Pliers
Phillips Screwdriver
Flat-blade Screwdriver
1/4" Nutdriver
Level
#' DFA. METAL D UCT
(RECOMMENDED/
MATERIALS YOU WILL NEED
#' DUCT
#' DFA FLEXBLE METAL ( SEMFREGED}
CLAMPS (2}
ULLISTED TRANSITION
DUCT
(IFNEEDED}
OR
P
KITWXO8XlO077
(INCLUDES
2 ELBOWS}
#' SPRING
CLAM PS(2}
%
#' DIA. M ETAL
ELBOW
%
EXHAUST
SAFETY
HOOD
GLASSES
#' DFA. FLEXBLE M ETAL (FOEL TYPE}
_
3/#'STRAEN
ULLISTED TRANSITION
DUCT
x,4
(iFNEEDED,}
DUCT T APE
GLOVES
RELIEF
4"COVER P LATE ( iFNEEDED/
ULRECOGNIZED
(KiT WE1M454}
APPLIANCE
POWER
CORD KIT
(NOT PROVIDED/
ULRATED
120/2@V,}OA
WITH 3 OR4PRONGS,
IDENTIFYTHE
PLUG
TYPE A SPER THE
HOUSE RECEPTACLE
BEFORE PURCHASING
LiNE CORD,
PARTS SUPPLIED
1 Cable Tie
%
oo
2 Rubber Washers
2 Stainer Screens/
Rubber Washers
(washers may be in water hoses)
2 Washer Hoses
Printedin Mexico
233DI835PO02
31-16652-5
12-12
GE
Publicidad
Tabla de contenido
