Trimming A Tree (Pruning); Saw Maintenance - Worx WG322 Manual De Instrucciones

Switch(31) (See Figure P6). This will turn
Pole Saw on. Releasing On/off Switch will
turn Pole Saw off. Make sure saw is running
at full speed before starting a cut.
6. When starting a cut, place moving chain
against wood. Hold Pole Saw firmly in
place to avoid possible bouncing or skating
(sideways movement) of saw.
7 . Guide Pole Saw using light pressure. Do not
force Pole Saw. The motor will overload and
can burn out. It will do the job better and
safer at the rate for which it was intended.
8. Remove Pole Saw from a cut with saw
running at full speed. Stop Pole Saw by
releasing trigger. Make sure chain has
stopped before setting Pole Saw down.

TRIMMING A TREE (PRUNING)

WARNING: Avoid kickback.
Kickback can result in severe injury
or death.
See Kickback, to avoid risk of kickback.
WARNING: Do not operate Pole Saw while
• in a tree
• on a ladder or any other unstable surface
• in any awkward position
You may lose control of Pole Saw
causing severe injury.
WARNING: Do not extend arms above
shoulders when using Pole Saw.
CAUTION: Seek professional help if
facing conditions beyond your ability.
Trimming a tree is the process of cutting limbs
from a living tree. Make sure your footing
is firm. Keep feet apart. Divide your weight
evenly on both feet.
Follow directions below to trim a tree.
1. Make first cut six inches from tree trunk on
underside of limb. Use top of guide bar to
make this cut. Cut 1/3 through diameter of
limb (See Figure P7).
2. Move two to four inches farther out on
limb. Make second cut from above limb.
Continue cut until you cut limb off.
3. Make third cut as close to tree trunk as
possible on underside of limb stub. Use
top of guide bar to make this cut. Cut 1/3
through diameter of stub.
4. Make fourth cut directly above third cut. Cut
down to meet third cut. This will remove
limb stub.
20V cordless chain saw, 20V 2-in-1 pole saw/
chain saw (WG322 WG322.9 WG323 WG323.9)

SAW MAINTENANCE

Follow maintenance instructions in this manual.
Proper cleaning of saw and chain and Guide Bar
maintenance can reduce chances of kickback.
Inspect and maintain saw after each use. This
will increase the service life of your saw.
NOTE: Even with proper sharpening, risk of
kickback can increase with each sharpening.
MAINTENANCE AND
STORAGE OF CHAIN SAW
1. Remove the battery pack
• When not in use
• Before moving from one place to another
• Before servicing
• Before changing accessories or
attachments, such as saw chain and guard
2. Inspect chain saw before and after
each use. Check saw closely if guard or
other part has been damaged. Check for
any damage that may affect operator safety
or operation of saw. Check for alignment or
binding of moving parts. Check for broken
or damaged parts. Do not use chain saw if
damage affects safety or operation. Have
damage repaired by authorized service
center. To locate an authorized service
center, visit www.worx.com
3. Maintain chain saw with care.
• Never expose saw to rain or direct
moisture.
• Keep chain sharp, clean, and lubricated for
better and safer performance.
• Follow steps outlined in this manual to
sharpen chain.
• Keep handles dry, clean, and free of oil and
grease.
• Keep all screws and nuts tight.
• Keep battery pack from heat, oil, and sharp edges.
4. When servicing, use only identical
replacement parts.
5. When not in use, always store chain saw
• in a high or locked place, out of children's reach
• in a dry place
• with Bar and Chain Storage/Transportation
Cover (9) in place
Bar Maintenance
To maximize bar life, the following bar
maintenance is recommended.
The bar rails that carry the chain should be
21
EN