Makita CC301D Manual De Instrucciones página 8

ASSEMBLY
CAUTION:
Always be sure that the tool is
switched off and the battery cartridge is removed
before carrying out any work on the tool.
Installing or removing diamond
wheel
CAUTION:
Use only the Makita wrench to
install or remove the diamond wheel.
CAUTION:
When installing the diamond
wheel, be sure to tighten the bolt securely.
CAUTION:
Always install the diamond wheel
so that the arrow on the diamond wheel points in
the same direction as the arrow on the diamond
wheel case. Otherwise the wheel rotates in reverse,
LW PD\ FDXVH SHUVRQDO LQMXU\
Fig.7: 1. Shaft lock 2. Hex wrench 3. Tighten
4. Loosen
Fig.8: 1. Hex bolt 2. 2XWHU ÀDQJH 3. Diamond wheel
4. ,QQHU ÀDQJH 5. Arrow
To remove the diamond wheel, press the shaft lock fully
so that the diamond wheel cannot revolve and use the
hex wrench to loosen the hex bolt counterclockwise. Then
UHPRYH WKH KH[ EROW RXWHU ÀDQJH DQG GLDPRQG ZKHHO
To install the diamond wheel, follow the removal pro-
cedure in reverse. Make sure the diamond wheel is
installed so that the arrow on the wheel points in the
same direction as the arrow on the diamond wheel
case.
BE SURE TO TIGHTEN THE HEX BOLT SECURELY.
Fig.9: 1. Hex bolt 2. 2XWHU ÀDQJH 3. Diamond wheel
4. ,QQHU ÀDQJH 5. Protrusion (bigger side)
NOTE: ,I DQ LQQHU ÀDQJH LV UHPRYHG E\ FKDQFH
LQVWDOO WKH LQQHU ÀDQJH VR WKDW LWV SURWUXVLRQ ELJJHU
VLGH IDFHV LQVLGH DV VKRZQ LQ WKH ¿JXUH
Hex wrench storage
Fig.10: 1. Hex wrench
When not in use, store the hex wrench as shown in the
¿JXUH WR NHHS LW IURP EHLQJ ORVW
Installing water supply
Loosen the screw A.
Slide the tank holder all the way over the motor housing
so that the notch of the band (part of the tank holder)
LV SRVLWLRQHG MXVW EHORZ WKH VFUHZ KHDG RI WKH WRRO DV
illustrated.
Then tighten the screw A.
Fig.11: 1. Screw A 2. Tank holder 3. Motor housing
4. Notch of the band (part of the tank holder)
5. Screw head of the tool
Attach the tank on the tank holder so that the tank
KROGHU ¿WV EHWZHHQ WKH VWHS DQG GRWV &RQQHFW WKH FDS
on the tube end to the mouth of the tank. Turn the tank
clockwise. Then tighten the screw B.
Fig.12: 1. Tank 2. Tube 3. Screw B
Water supply
CAUTION:
:KHQ ¿OOLQJ WKH WDQN ZLWK ZDWHU EH
careful not to let the tool get wet.
Be sure that the water supply cock is closed before
¿OOLQJ WKH WDQN ZLWK ZDWHU 2SHQ WKH FDS RQ WKH WDQN DQG
¿OO WKH ZDWHU 5HFDS WKH WDQN
Fig.13: 1. Water supply cock 2. Close 3. Open
Fig.14: 1. Cap 2. Open
OPERATION
CAUTION:
This tool should only be used on
horizontal surfaces.
CAUTION:
Be sure to hold the workpiece
¿UPO\ GRZQ RQ D VWDEOH EHQFK RU WDEOH GXULQJ
operation.
CAUTION:
Do not twist or force the tool in the
cut, or the motor may be overloaded or the work-
piece may break.
CAUTION:
Do not use the tool with the dia-
mond wheel in an upward or sideways position.
CAUTION:
The wheel for this tool is a wet-
type diamond wheel for glass and tile applica-
tions. Be sure to feed water to the diamond wheel
during operation.
CAUTION:
If the cutting action of the diamond
wheel begins to diminish, dress the cutting edge
of the wheel using an old discarded coarse grit
bench grinder wheel or concrete block. Dress by
pressing lightly on the outer edge of the diamond
wheel.
Fig.15
+ROG WKH WRRO ¿UPO\ 6HW WKH EDVH SODWH RQ WKH ZRUNSLHFH
to be cut without the wheel making any contact.
Then turn the tool on and wait until the wheel attains
full speed.
)HHG ZDWHU WR WKH ZKHHO E\ DGMXVWLQJ WKH ZDWHU VXSSO\
FRFN WR REWDLQ D JHQWOH ÀRZ RI ZDWHU
Move the tool forward over the workpiece surface,
NHHSLQJ LW ÀDW DQG DGYDQFLQJ VPRRWKO\ XQWLO WKH FXWWLQJ
is completed. Keep your cutting line straight and your
speed of advance uniform.
)RU ¿QH FOHDQ FXWV FXW VORZO\ :KHQ FXWWLQJ JODVV
plate 5 mm (3/16") thick, cut at about 250 mm/min
(9-7/8"/min). When cutting tile 10 mm (3/8") thick, cut
at about 300 mm/min (11-13/16"/min).) Also slow down
as you complete a cut to avoid breaking or cracking the
workpiece being cut.
NOTE: When the battery cartridge temperature is
low, the tool may not work to its full capacity. At this
time, for example, use the tool for a light-duty cut for
a while until the battery cartridge warms up as high
as room temperature. Then, the tool can work to its
full capacity.
NOTE: Make sure that the water supply cock is
closed before operation.
8 ENGLISH