Multiplex Easy Srat 3 Instrucciones De Montaje página 17

Assembly instructions
16. Installing the tailplane frame
To guarantee a secure seating, the tailplane frame
6
the recess of the tailplane . Fig. 18
17. Attaching the tailplane
First withdraw the tailplane slider
6
and push the slider back in as far as it will go to secure the tailplane.
Do not glue it! The tailplane should be left detachable for safe, convenient
transport. To remove the tailplane, press the tailplane clips
with two fingers, and at the same time pull the tailplane slider
the tailplane can now be removed. Fig. 19
18. Connecting the elevator
Slip the inner pushrod for the elevator through the hole in the swivel barrel
㉓
, and check the servo neutral position once more before tightening
㉔
the allen-head grubscrew . We recommend that you apply a drop of
medium-strength thread-lock fluid to the grubscrew to prevent it working
loose over time. Fig. 20
19. Releasing the control surfaces
Use a sharp balsa knife to remove the foam at the lateral ends of the
control surfaces, cutting along the moulded-in channels. Repeatedly
move the control surfaces to and fro in order to loosen the integral hinges
and render them freemoving. Do not separate the control surfaces!
Fig. 21
20. Attaching the servo well covers
Press the left and right servo well covers
both sides of the fuselage. They should not be glued in place, as you may
have to replace the servos at some time. Fig. 22
21. Installing the wing joiner channel cover
Carefully glue the wing joiner channel covers
7 8
panels and . Take particular care to avoid glue running onto the
surfaces which will later make contact with the wing joiner
㊿
that the wing joiner is a snug fit in the wings, but only when you are
absolutely confident that there is no active adhesive inside the channel.
If you neglect this, you could find that the model is glued together
permanently. Fig. 23
22. Attaching the rudder horns to the aileron
Recesses of the ailerons on the wings
㉒ 1
plates / through the rudder horns using two screws each
㉒ 4
/ . Fig. 24
23. Preparing the aileron servos
See "10. Preparing the servos".
㊼
must be glued in
㊽
slightly, then insert the tailplane
㊹
together
㊽
down;
⓫ ⓬
and into the openings in
9 ⓾
and in the wing
㊿
. Check
7 8
+ . Screw both counter
24. Installing the aileron servos
Fit the pre-formed aileron pushrods
the outside of the servo output arms. Use hot glue to glue the servos into
the recesses and feed the servo cables in the cable ducts through the
wings. Feed the aileron pushrod with "Z"
once more that the servos are at centre before tightening the grubscrews
㉔
in the swivel barrels. We recommend applying a drop of medium-
strength thread-lock fluid to the grubscrews to prevent them working
loose. Fig. 25
25. Servo lead length, aileron connections
Draw the servo leads out of the wings
the fuselage. Fig. 26
26. Installing the cable sleeves
To avoid kinking the aileron servo leads, glue 18 mm lengths of snake
outer sleeve (3 mm Ø / 2 mm Ø) in the recess where the cables exit the
wing. Fig. 27
27. Installing the firewall
㊵
Glue the firewall in place using thick cyano. Don't use activator for
this joint, as you will need a certain amount of time to position and align
the firewall correctly. Fig. 28
28. Gluing the cowl screw support in place
㊷
Glue the cowl screw support
Fig. 29
29. Installing the motor
Fix the motor in place using two M3 x 6 screws. Apply a drop of medium-
strength thread-lock fluid to the screws. The cable outlet on the motor
points to the right in the direction of flight. The motor cables are laid
behind the glued-in cable guide. Fig. 30
30. Installing the motor cowl
㉚
Fit the three screws to secure the motor cowl
31. Assembling the propeller

Attach the propeller blades
dowel pins 62. Fig. 32
Slip the taper collet through the driver

propeller boss . The washer
fitted from the other side. Screw the M6 nut

Fit the taper collet on the motor shaft and tighten the nut firmly before
fitting the spinner. Fig. 33 + 34

Fit the O-ring through the spinner cone
㉖
through the second hole from
㉖
into the cardan bolt. Check
7 8
+ where the wing meets
at the front end of the motor pod.
㊶
. Fig. 31

to the propeller boss using the two

and place this assembly in the

and the shakeproof washer

on the taper collet

. Fig. 35
EN

are

.
17