To Pick Up Water; To Pick Up Dust And Dirt; To Use Stripper Applicator - Advance Sprite 16 Instrucciones De Uso

TO PICK UP WATER

1 If the machine has been used for dry pick-up, remove the Filter Assembly System (if used).
2 Place the Dome Lid (2) on top of the Recovery Tank (3). Make sure that the Main Power Switch (1) is in the OFF position, then plug the Power Cord (6) into a
properly grounded wall outlet.
3 Attach the Recovery Hose (8) and the Vac Motor Hose (12) to the Dome Lid (2).
4 Connect the other end of the Recovery Hose (8) to the Squeegee or Wand. Accessory hoses, wands and other attachments are available from your local
Advance Dealer.
5 Turn the Main Power Switch (1) ON.
6 Release the Squeegee Raise/Lower Pedal (4) to lower the Squeegee to the fl oor. The Squeegee will pick up while moving forward or in reverse.
7 Add a defoamer chemical when picking up soapy water. To add defoamer, fi rst turn the Main Power Switch (1) OFF. Then remove the Dome Lid (2) and
pour the defoamer chemical into the Recovery Tank (3). See the manufacturer's recommendations for the proper amount. Put the Dome Lid (2) back on the
Recovery Tank (3) and turn the Main Power Switch (1) ON. Add defoamer each time the tank is emptied.
8 The Recovery Tank (3) has an automatic fl oat shutoff to block the vacuum system when the tank is full. You can tell when the fl oat closes by the sudden
change in the sound of the vacuum motor. When the fl oat closes, the tank must be emptied. The machine will not pick up water with the fl oat closed.

TO PICK UP DUST AND DIRT

1 If the machine has been used for wet pick-up, empty the Recovery Tank (3), rinse it out and dry it completely.
NOTE: The optional Filter Assembly System can also be installed over the fl oat cage on the Dome Lid (2) for additional exhaust air fi ltration during dry
pickup. The Filter Assembly System comes with installation instructions when ordered.
2 Then put the Dome Lid (2) on top of the Recovery Tank (3).
3 Attach the Recovery Hose (8) and the Vac Motor Hose (12) to the Dome Lid (2).
4 Connect the other end of the hose to a wand fi tted with a dry pick-up tool. Accessory hoses, wands and other attachments are available from your local
Advance Dealer.
5 Plug the Power Cord (6) into a wall outlet and turn the Main Power Switch (1) ON.

TO USE STRIPPER APPLICATOR

1 If the machine has been used for dry pick-up, remove the Filter Assembly System (if used).
2 Detach Power Cord from the machine at the pigtail plug outlet.
3 If the machine has been used for wet pick-up, empty the Recovery Tank (3), and rinse it out.
4 Place the chemical solution you are using into the Recovery Tank (3) and do not fi ll past the MAX water level mark on the Water Level Gauge (16).
5 Place the Dome Lid (2) on top of the Recovery Tank (3). Make sure that the Main Power Switch (1) is in the OFF position.
6 Remove the Squeegee tool (9) and install the Stripper Applicator Assembly (14) to the front mount using the two Thumb Nuts (13) to secure. Connect the
hose from the Stripper Applicator Assembly (14) to the Two-way Ball Valve (15).
7 Release the Squeegee Raise/Lower Pedal (4) to lower the Stripper Applicator Assembly to the fl oor. The Applicator is used while moving/pulling the machine
in reverse.
8 Solution fl ow rate to the Applicator is controlled by opening and closing the Two-way Ball Valve (15) at the lower left front corner of the Recovery Tank (3).
FORM NO. 56091026 - SPRITE 16 / SPRITE 16 PRO - A-7
ENGLISH / A-7