Technical Data; On-Off Switch - SUHNER UPC 2-R Instrucciones De Uso

• Auf einwandfreien Rundlauf achten und nur vibrationsarme
Werkzeuge verwenden. Dabei unbedingt auf die zulässige
Drehzahl achten.
Wartung
• Maschine trocken und sauber aufbewahren
• Vor allen Wartungsarbeiten an der Maschine den Stecker
aus der Steckdose ziehen!
• Kühlluftöffnungen an der Maschine müssen freigehalten
werden. Deshalb Motor regelmässig mit Druckluft durchbla-
sen.
• Das Winkelkopfgetriebeschmierfett nach jedem zweiten
Kohlenbürstenwechsel erneuern lassen.
Diese Arbeiten führt Ihr SUHNER-Service-Center sachge-
mäss und schnell aus.

Technical Data

Power Input
Power Output
No load speed
Wheel capacity
Sound pressure level
according to EN 50144
Vibration according to EN 50144
Spindle thread
(refer to enclosed spare part list)
Weight without cord set
Double Insulated
Voltage (refer to spare part list)
Machine components
1 Spindle
2 Right angle gear head
3 Side handle mount
4 Side handle
5 On/Off switch
6 Variable speed selector
7 Wrench 17 mm
8 Wrench 22 mm
Suitable Tools
9 Foam ring
10 Foam rubber support plate with self-adhesive 11
12 Felt polishing ring with lambswool mop 13
14 Abrasive impregnated nylon brush
Additional Abrasives and Tools
can be found in the the SUHNER catalogs
500 Watt
300 Watt
1'000-2'000 rpm
125 mm/5"
75 dB(A)
3,1 m/s 2
M 14 or 5/8" - 11"
1,5 kg
Class II
various
• Anschlusskabel regelmässig kontrollieren. Beschädigte
Kabel unbedingt ersetzen lassen.
• Reparaturen dürfen nur durch eine Elektrofachkraft aus-
geführt werden, andernfalls können Unfälle für den Benutzer
entstehen.
• Beanstandungen können nur anerkannt werden, wenn die
Maschine unzerlegt zurückgesandt wird.
Zubehör
Das Zubehör mit den dazugehörigen Bestellnummern ist in
den SUHNER-Katalogen aufgeführt.
Änderungen vorbehalten!
Safety Instructions
• Do not exceed max. operating speed of tool and clamping
element.
• Observe accurate mounting of tools. Run tool a few se-
conds under no load. Replace vibrating Wheels/discs at
once. Protect wheels from knocks and grease.
• Secure work, use clamps or vise to hold work.
• The grinder operator shall wear working gloves, safety
goggles or face shield at all times when the grinder is in
operation.
• If noise level exceeds 85 dB(A) at the work station, sound
insulation and hearing protection measures must be taken
by the operater.
• For additional personal protection, it is advisable to con-
nect tool to a ground fault circuit interrupter, (only in damp
areas).
For additional safety instructions
refer to enclosed brochure EW 39 210 01
Before start-up.
Voltage Warning
Before connecting tool to a power source, be sure the voltage
supplied is the same as specified on the name plate of the
tool. The power supply should not vary more than 10% above
or below the voltage indicated on the nameplate.

ON-OFF SWITCH

Before connecting power cord to receptacle, make sure that
switch 5 is in the Off -0- Position.
Operation conditions and instructions
This tool is equipped with an electronic variable speed tacho-
meter selector and an overload cut-out switch, which operates
as follows:
1. Soft start
2. With increased work pressure more current is drawn , which
virtually holds speed at a constant rpm.
3. If the motor is overloaded, the electronic cuts off the power.
In this event switch at once to OFF position, restart right
away to assure.
Cooling effect in no load mode. Repeated automatic cut off
GB
3