Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
Ampere Rating
Volts
120
240
More
Not More
Than
Than
0
6
6
10
10
12
12
16
Jigsaw Safety
WARNING: Before connecting a tool to a power source (mains switch power point receptacle,
outlet etc.) be sure that the voltage supply is the same as that specified on the nameplate of
the tool. A power source with a voltage greater than that specified for the tool can result in
serious injury to the user, and damage to the tool. If in doubt, do not plug in the tool. Using a
power source with a voltage less than the nameplate rating is harmful to the motor.
• Hold the power tool by insulated gripping surfaces only, when performing an operation
where the cutting tool may contact hidden wiring or its own cord. Contact with a "live" wire
will also make exposed metal parts of the power tool "live" and could give the operator an
electric shock.
• Do not reach underneath the workpiece. The guard cannot protect you from the blade below
the workpiece.
• Never hold piece being cut in your hands or across your leg. Secure the workpiece to a
stable platform. It is important to support the work properly to minimise body exposure,
blade binding, or loss of control.
For safety relating to protective clothing/equipment and general health hazards relating
to power tools; refer to General and Electrical Safety sections in this manual
• Do not allow anyone below 18 years of age operate this jigsaw
• Ensure there is adequate lighting
• Rags, cloths, cord and string etc should not be left around the work area
• Keep the area free of tripping hazards
• Inspect the workpiece and remove all embedded objects before starting work
• Support or clamp the workpiece to avoid vibration, and ensure a good cut
• See specification section of this manual for the correct type of blade. Incorrect blades may
not be secured correctly, causing a safety hazard
• Only use blades that are in good condition
• If you are interrupted when operating the saw, complete the process and switch off before
looking up
• Keep your hands away from the underside of the workpiece
• Ensure that an appropriate blade is used for the material being cut Ensure all supports and
power cables are completely clear of the cutting path
• Where guards exist, ensure they are in place
• Do not put pressure on the tool. Allow the blade to cut at its own pace. This will produce
better results and maximise the service life of the tool
• Before cutting, check that there is sufficient clearance for the blade under the workpiece
• Always keep the shoe pressed against the workpiece
• Do not attempt to cut material thicker than detailed in the specifications section of this
manual
• Do not force the blade to bend or twist whilst cutting
• If a cut does not extend to the edge of the workpiece, allow the blade to come to a complete
stop before lifting it from the workpiece
• Do not use your hands to remove sawdust, chips or waste close by the blade
• Do not reach over the blade to remove waste or off-cuts
• Blades heat up during use. Allow to cool completely before handling
GB
• If a blade jams, disconnect the machine from the power supply prior to releasing the blade
• Periodically check that all nuts, bolts and other fixings, tighten where necessary
Cutting tool safety
WARNING. Before connecting a tool to a power source (mains switch, power point, receptacle,
outlet, etc.) be sure that the voltage supply is the same as that specified on the nameplate of
the tool. A power source with a voltage greater than that specified for the tool can result in
serious injury to the user, and damage to the tool. If in doubt, do not plug in the tool. Using a
power source with a voltage less than the nameplate rating is harmful to the motor.
8
Table A
Total length of cord in feet
25
50
100
150
50
100
200
300
Minimum gage for cord
18
16
16
14
18
16
14
12
16
16
14
12
14
12
Not Recommended
Use the correct cutting tool
• Ensure the cutting tool is suitable for the job. Do not assume a tool is suitable without
checking the product literature before use
Protect your eyes
• Always wear appropriate eye protection when using cutting tools
• Spectacles are not designed to offer any protection when using this product; normal lenses
are not impact resistant and could shatter
Protect your hearing
• Always wear suitable hearing protection when tool noise exceeds 85dB
Protect your breathing
• Ensure that yourself, and others around you, wear suitable dust masks
Protect your hands
• Do not allow hands to get close to the cutting wheel or blades. Use a suitable push stick for
shorter workpieces with appropriate power tools
Be aware of others around you
• It is the responsibility of the user to ensure that other people in the vicinity of the work area
are not exposed to dangerous noise or dust and are also provided with suitable protective
equipment
Hidden objects
• Inspect the workpiece and remove all nails and other embedded objects before cutting
• Do not attempt to cut material that contains embedded objects unless you know that the
cutting tool fitted to your machine is suitable for the job
• Walls may conceal wiring and piping, car body panels may conceal fuel lines, and long
grass may conceal stones and glass. Always check the work area thoroughly before
proceeding
Beware of projected waste
• In some situations, waste material may be projected at speed from the cutting tool. It is the
user's responsibility to ensure that other people in the work area are protected from the
possibility of projected waste
Fitting cutting tools
• Ensure cutting tools are correctly and securely fitted and check that wrenches / adjusters
are removed prior to use
• Only use cutting tools recommended for your machine
• Do not attempt to modify cutting tools
• Ensure blades are sharp, in good condition and correctly fitted
• Do not attempt to resharpen blades that are not suitable for resharpening, these may
include specially hardened blades or blades made from hardened alloys typically containing
tungsten
• Blades that can be resharpened should be resharpened only according the blade
manufacturer's instructions. These may include a limited number of times the blade can be
resharpened
• Sharpened blades should be more thoroughly inspected before use and replaced
immediately if there is any doubt about their condition and suitability for use
• In the event blades encounter an embedded object in use that the blades are not suitable
for, blades should be replaced immediately
Direction of feed
• Always feed work into the blade or cutter against the direction of movement of the blade or
cutter
Beware of heat
• Cutting tools and workpieces may become hot in use. Do not attempt to change tools until
they have been allowed to cool completely
Control dust / swarf
• Do not allow dust or swarf to build up. Sawdust is a fire hazard, and some metal swarf is
explosive
• Be especially careful when cutting wood and metal. Sparks from metal cutting are a
common cause of wood dust fires
• Where possible, use a dust extraction system to ensure a safer working environment
Publicidad
Tabla de contenido
