Technical Specifications - Hudora Laufrad Cruiser 12 Instrucciones De Montaje

INSTRUCTIONS ON ASSEMBLY AND USE
EN
CONGRATULATIONS ON PURCHASING YOUR PRODUCT!
Please read these instructions carefully. The instructions are an integral compo-
nent of the product. Therefore, please store them and the packaging carefully in
case questions arise in the future. Please always include these instructions
when giving the product to a third party. This product must be assembled by an
adult. This product is not designed for industrial use. The use of the product
requires certain capabilities and skills. Always adjust according to the age of the
user and use for the purpose it has been designed for.

TECHNICAL SPECIFICATIONS

Skate:
Item number:
Handlebar height adjustable:
Saddle height adjustable from: 35 - 41.5 cm | 36.5 - 41.5 cm
Maximum carrying capacity:
If you have assembly problems or would like further information on the product,
we have all you need and more at http://www.hudora.de/.
CONTENTS
1 x Walker bike: Front wheel fork, Frame with back wheel, Handlebars, Front
wheel, Mudguard for the front wheel, Saddle, Small parts
1 x Usage instructions
Other parts which may be included with the delivery in some circumstances are
not required.
SAFETY INSTRUCTIONS
• Warning! Not suitable for children under 36 month because of the risk of
swallowing small parts. Choking Hazard!
• This product is only suitable for smooth paved surfaces. Do not use it on
public roads.
• The running bike is only intended for use by one person.
• Warning! Please ensure that your child wears the appropriate protective
clothing (helmet).
• Warning! Driving and stopping can also be done with the application of the
foot; the impeller must therefore be used only with shoes. There is a risk of
injury.
• Do not allow your child to ride the running bike at twilight, at night or in poor
visibility.
• To prevent putting your child or others in danger, you should not let the run-
ning bike be used on roads or thoroughfares or on slopes or hills. Avoid using
it in the proximity of stairs or open water.
• Inspect the running bike before each use to ensure that all parts are still fixed
in place correctly and that the running bike is functioning as intended.
• For children from 3 to 5 years of age only.
• This product contains small parts which could cause asphyxia if swallowed.
Supervise children during the assembling. This product must be assembled
by an adult. Children should only use the product when they are under adult
supervision.
• Please ensure that your child keeps both hands securely on the handlebars
in order to maintain better control over the bike.
• The use of the product requires specific skills and knowledge to be able to
avoid injury to the user and third parties through a crash or collision.
• Warnings! Protective equipment should be worn. Not to be used in traffic. 50
kg max.
ASSEMBLY INSTRUCTIONS (DIAGRAM 1 - 6)
1. Attach the mudguard for the front wheel to the front fork using a screw,
washer and nut. The mudguard for the back wheel is pre-mounted.
2. Put the front wheel into the fork and tighten thenuts. Make sure the hooks in
the lock washers are in their intended holes in the fork.
3. Push the fork from below through the frame, as shown in the diagram 3.
Make sure there is a plastic disc above and below the frame shaft.
All images are examples of the design.
Cruiser walker bike 12"
10066, 10067 | 10088, 10089
from 50 - 57 cm | 50 - 56.5 cm
50 kg
4. Push the covering cap over the handlebar shaft. Then push the handlebar
clamp onto the fork shaft from above. Make sure that the handle clamp fits
exactly onto the fork shaft and is pushed down as far as possible. Check that
the rings and the guide sleeves are fully fitted into the frame. Now insert the
handlebars into the fork shaft from above. In order to set the handlebars at
the highest position, pull out the vertical handlebar shaft to any further, as this
may lead to accidents. Make sure that the handlebar shaft is fixed in correct
alignment with the front wheel before screwing the handlebars tightly into
place.
5. Push the covering cap over the handlebar clamp.
6. Insert the saddle into the seat post. Make sure that the maximum seat height
is not exceeded, i.e. do not pull the seat post out beyond the MAX marking, as
exceeding the maximum seat height may lead to serious injury.
SETTING UP THE BAND BRAKE (DIAGRAM 7)
Your trainer bike has a belt brake at the rear end. It is operated with the brake
handle on the handlebar. The brake system is pre-mounted and pre-adjusted.
However, before every use, ensure that the brake system functions without any
problem. It the brake is not effective enough, it can be easily adjusted. There are
many options, starting from the brake handle to the brake itself. The distance of
the brake handle from the grip can be adjusted with the adjusting screw. Tighten
it to decrease and loosen to increase the gap. The screw is basically to give your
child the correct grip, but a change will also affect the brake slightly. Loosening
of the screw will give the handle more room. Tightening of the screw reduces the
room and therefore the braking ability of the belt brake. The lock nut [A] at the
belt brake changes the brake cable run (Illus. 7). If you turn it towards the cable,
the cable run shortens and the braking is quicker. Fasten the lock nut [A] with a
counter nut [B]. You can also use the set screws [D]. They directly affect the belt
brake. The brake section presses itself closer to the axle if you fasten it in and
loosens correspondingly if you loosen the screw. If all these options fail, you can
shorten the wire drawing. Loosen the nut [C], pull the brake cable taut and re-
fasten it. Take help from a mechanic if these options fail, because a faulty brake
can lead to grave injuries or damages! Before the bicycle is used for the first
time, activate the brake lever several times and check whether all of the screws
have been tightened and the brakes are working perfectly.
MAINTENANCE AND STORAGE
Use a dry or damp cloth only to clean the product; do not use special cleaning
agents! Check the product for damage or traces of wear and tear before and
after each use. Do not make any structural changes. For your own safety, please
use original spare parts only. These can be sourced from HUDORA. If parts be-
come damaged or if sharp edges or corners should develop, the product may not
be used any more. If in any doubt, please contact our service team (http://www.
hudora.de/service/). Store the product in a safe place where it is protected from
the elements, cannot be damaged, and cannot injure anyone.
DISPOSAL ADvICE
At the end of the product's life, please dispose of it at an appropriate collection
point in your area. Local waste management companies will be able to answer
your questions on this.
SERvICE
We make every effort to deliver faultless products. If faults do arise however, we
put just as much effort into rectifying them. Therefore, you can find numerous
information on the product, replacement parts, solutions to problems and lost
assembly manuals at http://www.hudora.de/service.
4/8