Technical Specifications - Hudora Advanced Alu Instrucciones De Montaje Y De Uso

INSTRUCTIONS ON ASSEMBLY AND USE
EN
CONGRATULATIONS ON PURCHASING THIS PRODUCT!
Please read these instructions carefully. The instructions are an integral component of
the product. Therefore, please store them and the packaging carefully in case questions
arise in the future. Please always include these instructions when handing on the product
to a third party. This product must be assembled by an adult. This product is designed for
private/domestic use only. This product is not designed for commercial/industrial use. The
use of the product requires certain capabilities and skills. Always adjust according to the
age of the user and use for the purpose it has been designed for.

TECHNICAL SPECIFICATIONS

Item: Balance bike Advanced Alu
Item number: 10425/00, 10426/00, 10427/00
Adjustable saddle height: from approx. 32 – 44,5 cm
Recommended leg height: 35 – 50 cm
Recommended body size: 90 – 115 cm
Maximum user weight: 35 kg
Purpose: Balance bike for locomotion of children with a max.
user weight of 35 kg on non-public roads.
If you have assembly problems or would like further information on the product, we have
all you need and more at http://www.hudora.de/.
CONTENTS
1 x Balance bike with tool and screw set (see parts list p. 2)
1 x These instructions
Other parts which may be included with the delivery in some circumstances are not re-
quired.
SAFETY INSTRUCTIONS
• WARNING! Protective equipment should be worn. Not to be used in traffic.
35 kg max.
• WARNING! Please ensure that your child wears the appropriate protective clothing
(helmet).
• WARNING! Driving and stopping can also be done with the application of the foot; the
balance bike must therefore be used only with shoes. There is a risk of injury.
• This toy has to be used with caution since the use of the product requires specific skills
and knowledge to be able to avoid injury to the user and third parties through a crash
or collision.
• This product is only suitable for smooth paved surfaces. Do not use it on public roads.
• The balance bike is only intended for use by one person.
• Do not allow your child to ride the balance bike at twilight, at night or in poor visibility.
• To prevent putting your child or others in danger, you should not let the balance bike
be used on roads or thoroughfares or on slopes or hills. Avoid using it in the proximity
of stairs or open water.
• Inspect the balance bike before each use to ensure that all parts are still fixed in place
correctly and that the balance bike is functioning as intended.
• This product contains small parts which could cause asphyxia if swallowed. Supervise
children during the assembling. This product must be assembled by an adult. Children
should only use the product when they are under adult supervision.
• Please ensure that your child keeps both hands securely on the handlebars in order to
maintain better control over the bike.
• Recommended for use by children from approx. 3 years of age.
INSTRUCTIONS ON ASSEMBLY (Fig. 1 – 8)
1. The fork, handlebar stem and rear wheel are pre-assembled on delivery.
2. Unscrew the 4 Allen screws at the front of the handlebar stem completely as shown
in figure 1 and remove the front element of the handlebar clamp as shown in figure 2.
3. Position the handlebars centrally in the recess of the handlebar stem and then screw
the front element back on. The brake lever is located to the right of the handlebar
stem as shown in figure 3. We recommend tightening the 4 Allen screws only slightly
at first and checking the correct position of the handlebars again and adjusting them
if necessary before tightening the screws.
4. Now mount the front wheel. First loosen the screws with the washers from the axle
and insert the axle ends into the holes at the lower end of the fork as shown in figure 4.
5. Now screw the previously loosened screws and washers from the outside into the
internal thread of the axles as shown in figure 5. Mount the screws evenly to reduce
the tension in the fork and ensure the front wheel is centered. Figure 6 shows a
correctly mounted front wheel.
6. Insert the saddle into the seat tube and tighten the bolt on the seat clamp to the
desired saddle height as shown in figure 7. Make sure you do not exceed the ma-
ximum seat height by not pulling the seat post out further than the „MAX" mark, as
exceeding the maximum seat height can cause serious injury. Also make sure that the
saddle is correctly aligned parallel to the frame as shown in figure 8.
7. Then attach the handlebar impact protection to the handlebar stem using the hook-
and-loop fasteners.
8. Finally, inflate the tyres.The maximum air pressure should not exceed 2.4 bar. When
inflating, please make sure that the tube lies evenly in the rim and is not twisted. The
casing must also sit evenly on the rim and must not push the tube in at any point.
All images are examples of the design.
HOW TO SET UP THE BRAKES (Fig. 9 - 10)
Your balance bike has a belt brake at the rear end. It is operated with the brake handle
[A] on the handlebar (fig. 9 & 10). The brake system is pre-mounted and pre-adjusted.
However, before every use, ensure that the brake system functions without any problem.
It the brake is not effective enough, it can be easily adjusted. There are many options,
starting from the brake handle to the brake itself. The distance of the brake handle from
the grip can be adjusted with the adjusting screw [B]. Tighten it to decrease and loosen to
increase the gap. The screw is basically to give your child the correct grip, but a change
will also affect the brake slightly. Loosening of the screw will give the handle more room.
Tightening of the screw reduces the room and therefore the braking ability of the belt
brake. The lock nut [D] at the belt brake changes the brake cable run (fig. 10). If you turn
it towards the cable, the cable run shortens and the braking is quicker. Fasten the lock
nut [D] with a counter nut [C]. You can also use the set screws [F]. They directly affect
the belt brake. The brake section presses itself closer to the axle if you fasten it in and
loosens correspondingly if you loosen the screw. If all these options fail, you can shorten
the wire drawing. Loosen the nut [E], pull the brake cable taut and refasten it. Take help
from a mechanic if these options fail, because a faulty brake can lead to injury or damage!
Before the balance bike is used for the first time, activate the brake lever several times and
check whether all of the screws have been tightened and the brakes are working perfectly.
MAINTENANCE AND STORAGE
Use only a dry or damp cloth to clean the product; do not use special cleaning agents!
Check the product for damage or traces of wear and tear before and after each use. Do
not make any structural changes. For your own safety, please use original spare parts only.
These can be sourced from HUDORA. If parts become damaged or if sharp edges or cor-
ners should develop, the product may not be used any more. If in any doubt, please contact
our service team (http://www.hudora.de/service/). Store the product in a safe place where
it is protected from the elements, cannot be damaged, and cannot injure anyone.
DISPOSAL ADVICE
At the end of the product's life, please dispose of it at an appropriate collection point
provided in your area. Local waste management companies will be able to answer your
questions on this.
SERVICE
We make every effort to deliver faultless products. If faults do arise however, we put just
as much effort into rectifying them. You can find numerous information on the product, re-
placement parts, solutions to problems and lost assembly manuals at http://www.hudora.
de/service/.
6/12