Miller Edge FALL PROTECTION SYSTEM Manual De Operación Y Mantenimiento página 10

4. Inspect for malfunctioning components, broken or missing pins and fasteners. Replace if
necessary.
5. Inspect wheels to ensure th
areas, excessive wear. Also, ensure that each wheel is securely fasten
6. Inspect brake jacks to ensure that each works properly and is capable of raising the unit when
crank handle has been rotated clock-w
7. Inspect all welds through out the unit for cracks, breaks, or corrosion.
8. Inspect syste m and all personal fall protection according to the manufacturer's instructions.
Forma l Inspection: A competent person must perform an annual inspection of the
co mponents.
Note: If the system has arrested a fall, an evaluation of the entire syst
subjected to impact loading shall be immediately removed from service and shall not be use
again for employee protection until inspected and determined by a competent person to be
undamaged and suitable for reuse.
W ARNING: If inspection reveals a defect in condition, immediately remove the unit from service.
VI. M AINTENANCE
A. S ERVICING
Servicing must only be carried out by a qualified person trained in the inspection and replacement of
this system. The company safety officer should maintain a record log of all servicing and inspection
dates for this unit. This unit a
subjected to fall arresting forc
questions.
B. CLEANING
Periodically clean the unit using a damp cloth and a non-abrasive mild soap or detergent. Towel dry.
C. STORAGE
Before storin g, clean the unit to remove any dirt, grease or other materials that may have
a ccumulated. Store in a clean dry area when not in use.
VII. WARNING LABELS
ATTACH LIFELINE HERE
WARNING!
ONLY 1 PERSON PER ANCHORAGE IS PERMITTED AT ONE TIME.
CONNECTORS USED WITHIN THE SYSTEM MUST BE ABLE TO
SUPPORT 5,000 LBS. THE USE OF NON-APPROVED
COMPONENTS MAY CAUSE SERIOUS INJURY OR DEATH.
LB515 REV. A
WARNING!
DO NOT EXCEED SAFE WORK ZONE
FAILURE TO FOLLOW MANUFACTURER'S INSTRUCTIONS
MAY RESULT IN SERIOUS INJURY OR DEATH.
LEADING
EDGE
LB530 REV. A
at each rotates and moves freely and inspect for cuts, breaks, broken
ise to a complete stop.
:
nd all components of the system must be removed from service if
es. Contact Dalloz Fall Protection at 1-800-873-5242 if there are any
:
PUSH PIN
VERTICAL BOOM INSTALLATION
1. READ, UNDERSTAND AND FOLLOW ALL INSTRUCTIONS
BEFORE USING.
2. INSERT PUSH PIN THROUGH THE FRAME, VERTICAL BOOM
AND INSTALL HITCH PIN THROUGH PUSH PIN AS SHOWN.
WARNING: BE SURE THE HITCH PIN HAS BEEN INSTALLED.
FAILURE TO DO SO MAY RESULT IN SERIOUS INJURY
OR DEATH.
LIFTING RINGS
BOTH LIFTING RINGS MUST BE USED TO LIFT THE DEVICE.
WARNING!
DO NOT USE FOR FALL PROTECTION.
USING ONLY ONE LIFTING RING MAY CAUSE THE DEVICE TO
BECOME UNSTABLE OR UNBALANCED WHILE LIFTING.
FAILURE TO FOLLOW MANUFACTURER'S INSTRUCTIONS
MAY RESULT IN SERIOUS INJURY OR DEATH.
LB518 REV. A
ed.
em and components
HITCH PIN
PUSH PIN
1. READ, UNDERSTAND AND FOLLOW ALL INSTRUCTIONS
2. INSERT PUSH PIN THROUGH HORIZONTAL BOOM AND
WARNING: BE SURE THE HITCH PIN HAS BEEN INSTALLED.
FAILURE TO DO SO MAY RESULT IN SERIOUS INJURY
OR DEATH.
LB517 REV. A
entire system and all
d
HITCH PIN
HORIZONTAL BOOM INSTALLATION
BEFORE USING.
INSTALL HITCH PIN THROUGH PUSH PIN AS SHOWN.
LB516 REV. A
WARNING!
ENGAGED BRAKES BEFORE EACH
USE. FAILURE TO DO SO MAY
RESULT IN SERIOUS INJURY
OR DEATH.
BRAKE ENGAGEMENT:
ROTATE BRAKE HANDLE CLOCK-
WISE UNTIL HANDLE HAS
STOPPED.
BRAKE DISENGAGEMENT:
REVERSE ABOVE PROCEDURES
LB520 REV. A