Quick A 712 Manual Del Usuario página 17

POS. DESCRIPTION
17A Screw Aries base
17B Screw Flair base
18A Rope/chain stripper Aries base
18B Rope/chain stripper Flair base
19 Sensor
20 Screw for pressure lever
21A Black pressure lever
21B White pressure lever
22 Spring for gypsy pressure lever
23 Cover pin
24A base ovale Aries
24B Oval base Aries
24C Oval base white Flair
25 Oval base black Flair
26 Rope/chain stripper R base
27 Screw Rider base
28 Gasket/A-F - shaped jig
29 Gasket/R - shaped jig
30A Studs Aries base
30B Studs Flair base
31 Gearbox flange gasket
Top TG50
32 Gearbox 700/1000W Quick TG50
33 Gearbox 1400W
34 Washer
35 Spring washer
36 Nut
37 Washer
38 Self-locking nuts
39 O-ring
40 Gasket motorgearbox
41 Key
42A Electric motor 700W 12V
42B Electric motor 700W 24V
42C Electric motor 1000W 12V
42D Electric motor 1000W 24V
42E Electric motor 1400W 12V
42F Electric motor 1400W 24V
43A Motor casing watertight 700W
43B Motor casing watertight 10/1400W PCCCPM100000
44 Grommet 1000/1400W
45 Terminal board cover
46 Screw
47 Bottom gasket
48 Bottom protec cover
49 Cable outlet
AFR 700/1000/1400W - REV009B
CODE
MBV0516MXSC0
MBV0530MXSC0
MSN10VXP0000
Quick
MSN10VXD0000
SAKREED00000
ant to marine environments. In any case, any salt deposits
MSMVT1000000
on the outside must be removed periodically to avoid cor-
PDLVTD100000
rosion and damage to the equipment. The parts where salt
PDLVTD10W000
may have built up should be washed thoroughly with fresh
MMTND1000000
water.
MSR10X000000
SGMSC10V0000
Once a year, the drum and the gypsy are to be taken apart
SMPD10VW0000
as follows:
SMPD10VB0000
SGMSC10C0000
DRUM VERSION
MSN10CX00000
Use the handle (1) to loosen the bush (3); pull off the drum
MBV0620MXSC0
PGBSV1000000 (4) and the top clutch cone (5); loosen the fixing screws (17
PGBSC1000000
or 27) of the rope/chain stripper (18 or 26) and remove it.
MBP080807X00
Pull off the gypsy (6).
MBP080808X00
NO-DRUM VERSION
PGFLRDTG50000
Use the handle (1) to remove the gypsy cover (2); remove
SLMR10TG5000
the top clutch cone (5); loosen the fixing screws (17 or 27) of
MR1400000000
the rope/chain stripper (18 or 26) and remove it and pull off
MBR08X000000
MBR08XDE0000 the gypsy (6).
MBD08MXEN000
MBR061815X00
Clean all the parts removed to avoid corrosion, and grease
MBD06MXET000
the shaft thread (13 and 14) and the gypsy (6) where the
-
clutch cones (5) rest (use grease suitable for marine envi-
PGNP10000000
ronment) .
MBH050515F00
EMF071200000
Periodically grease the hinge pin (23) of the chain guide
EMF072400000
cover (16) (only windlasses with aluminium bases).
EMF101200000
EMF102400000
Remove any oxide deposits from the terminals of the elec-
EMF141200000
tric motor and the contactor unit; grease them.
EMF142400000
PCCCPM070000
PCGPMMR00000
PCCPPMMR0000
MBV02213AXSC
PGGPMFN00000
PCCPPMFN0000
PPM20B000000
MAINTENANCE
WARNING: make sure the electrical power to the
motor is switched off when working manually on the
windlass. Carefully remove the chain or rope from the
gypsy or the rope from the drum.
® windlasses are manufactured with materials resist-
GB
17