Handling; Assembly - Breezy 305 Manual De Instrucciones

C. HANDLING
1. Opening: Rest both hands on each of the seat upholstery support rails and press down until the seat and back
upholsteries become taut. Lower the footplates into the using position. As a safety measure, the footplates will always
be in an upright position before sitting or getting out of the chair in a forward movement. Warning: Do not place your
fingers between the seat upholstery and the seat tubes when opening or folding the wheelchair
2. Folding: First flip up the (platform) footplate or the individual footplates. Take hold of the sling from underneath in
the middle and pull upwards. The wheelchair will then fold up. To fold your wheelchair until it is as small as possible,
e.g., to put into a car, you can remove the footrests (depending on the model). For this purpose, open the latch from
the out-side and swing the footrest to the side. Then the footrest only has to be drawn out of the frame tubing.
3. Folding back-rests (models 315 and 310) (fig. 1) To fold down the back-rest, press the black buttons on the
components on the back-rest tubing and pull back the push handles.
4. Reclining back (4° - 55°) (Fig. 2): By pulling the 2 levers at the same time the backrest is released and can be
set to the required position. Releasing the 2 levers will lock the backrest automatically in the new position. To bring
the backrest back to the upright position, just move it (no release necessary) to the required position.
Caution: The reclining back is only to be used in combination with the active anti-tips setting
Caution: The reclining back is only to be used in combination with a stabilizer bar. Please always make sure that
the stabilizer bar is locked in place on both sides.
Caution: Before folding the wheelchair, make sure that the stabilizer bar is removed
Caution: In order to avoid any reduction in the cable function, you must make sure that the cables are not completely
taut.
Caution: When adjusting the back angle, be careful not to get your fingers caught.
Caution: Before adjusting the back angle, put the anti tip tubes in to the active position
5. elevating legrest (Fig. 3) To elevate:Lift your lower leg and press the release button. Pull the legrest upwards
and adjust it to the desired height. As soon as you release the button, the legrest will click back into place. To lower:
Lift your lower leg and press the release button to unlock the legrest to lower it. As soon as you release the button,
the legrest will click back into place. CAUTION: The elevating legrest is not allowed to be adjusted into the lowest
position to avoid any interference with the casters. CAUTION: Keep hands clear of the adjustment mechanism
between the frame and the movable parts of the legrest while elevating or lowering the legrest.
6. Hemiplegic propulsion wheels: To move forwards, push both rims forwards at the same time. To move backwards,
push both rims backwards at the same time. To move to the right, push the smaller, external rim. To move to the
left, push the larger, internal rim.
D. ASSEMBLY
1. Footrests (Fig. 4): The footrests can be rotated inwards or outwards by pressing the release latch and turning
the footrest in the desired position. To remove the footrest, press the release latch, rotate the footrest approximately
90º and lift.
2. Armrests (Fig. 5): The armrest can either be flipped back or can be detached from the chair. To flip arms back,
press the release latch and pull arm toward back of the wheelchair. To detach the armrest press the button located
on the back of the armrest and lift it. CAUTION: Make sure that the armrest is properly locked into place. Never lift
the wheelchair by the armrests as these parts are detachable and lifting the wheelchair by them may cause damage
to the chair and/or injury to the user.
3. Head-rest (Fig. 6): To install the head-rest, push the head-rest tubes into the tubes at the top of the back-rest
until the locking pins click into position in the holes. To remove it, press the locking pins and pull the head-rest up
until it comes off.
4. Reclining back-rest stabilising bar (Fig. 6): Installation: Insert the bar into the tubes on the back of the back-
rest. Press the locking pins and hold them down while inserting the stabilising bar, until the pins lock into place in
the holes in the bar. To remove the bar, reverse the process.
25