MSW -WP-10T Manual De Instrucciones página 12

Tabla de contenido

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 37
3.
Close the release valve near the manual pump lever by twisting it clockwise.
4.
Pump using the lever until the piston is near the work piece.
5.
Align the axis of the work piece and the piston to ensure symmetric pressure.
6.
With the piston by the work piece, monitor manometer readings to avoid overloading the press.
(Maximum press capacity 666bar / 9656psi -30TONNES).
7.
Apply pressure to the work piece by further pumping until desired result is achieved.
Retracting the piston:
1.
Stop using the lever and slowly open the release valve by twisting it anticlockwise. Secure the work
piece to prevent it from falling off the table during pressure release.
2.
Only remove the work piece when the piston is completely retracted.
MSW-WP-30T-P
Operation
Hydraulic Shop Press assembly:
53
52
51
50
49
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
22
48
47
46
45
44
43
42
41
40
39
54
55 56 57
38
37
36
35
34
33
32
31
30
29
27
28
Rev. 09.12.2016
No.
Description
Quantity
1.
Left support post
1
2.
Ø20 washer
8
3.
M20 bolt
8
4.
M10x15 bolt
8
5.
Ø10 washer
8
6.
Roller axle
4
7.
Roller
4
8.
M10x30 bolt
3
9.
Winch
1
10.
Winch support
1
11.
Ø10 washer
3
12.
M10 nut
3
13.
M10x30 bolt
2
14.
Pin
2
15.
Ø10 washer
2
16.
M10 bolt
2
17.
M10x15 bolt
4
18.
Ø10 washer
8
19.
M10 nut
8
20.
M10 bolt
8
21.
Base bracket support
4
22.
Base bracket
2
23.
Bottom bracket
1
24.
Ø10 washer
4
25.
M10 nut
4
26.
M10x30 bolt
4
27.
Right support post
1
28.
Lever
1
29.
Pump / pneumatic motor
1
Pressing (piston operation)
1.
Set worktable to the required height using the winch and steel cable. To do that set the arrestor by the
crank toothed wheel to the middle position, and secure it using two pins.
2.
If a pneumatic motor is used, connect a compressed air hose to the valve with a quick coupler.
3.
Position work piece on the worktable.
4.
Close the release valve near the manual pump lever by twisting it clockwise.
5.
Pump using the lever (of a pneumatic motor is used, press the button on the valve) until the piston is
near the work piece.
6.
Align the axis of the work piece and the piston to ensure symmetric pressure.
Rev. 09.12.2016
No.
Description
Quantity
30.
Adjustable worktable support
1
31.
Hydraulic hose
1
32.
Steel cable
2
33.
Ø5 washer
3
34.
M5x10 manometer bolts
3
35.
Manometer
1
36.
Worktable surface
2
37.
Ø10 washer
1
38.
M10x20 bolt
1
39.
Quick coupling
1
40.
Mounting plate
1
41.
Hydraulic split
1
42.
Ø10 washer
1
43.
Ø9x2.65 O-ring
1
44.
M10 nut
1
45.
Hydraulic hose
1
46.
Spring spacer
4
47.
Plate
2
48.
Upper actuator coupling
1
49.
Actuator
1
50.
Upper crossbeam
1
51.
M20x40 bolt
8
52.
Cylinder plate
1
53.
M8x65 bolt
4
54.
Lower actuator coupling
55.
Ø12.5x1.8 O-ring
1
56.
Middle manometer coupling
1
57.
Manometer coupling
1
23

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

Msw-wp-30tMsw-wp-30t-pMsw-wp-50t-p

Tabla de contenido