Intended Use Of The Machine; Technical Specifications; Assembling The Machine - MSW -WP-10T Manual De Instrucciones

14. Do not exceed the maximum press capacity and/or maximum actuator displacement (if in doubt use
the pressure gauge to determine the applied pressure).
15. On finishing work open the release valve.
16. Avoid situations where the work piece can fall off the press worktable.
17. Only work on one piece at a time.
18. The machine is not designed for long-term loading.
19. Never introduce any modifications to the machine.
20. Do not perform mechanical or similar works (welding, cutting, etc.) on the work piece.
21. After completion of work, the machine must be secured against unauthorized use.
22. The machine must be regularly controlled and its damaged or worn and torn parts must be replaced
with new ones
by an authorised service
23. The work piece accidentally slipping or falling off the worktable constitutes a risk of injury or death.
24. When transporting and handling the hydraulic press between the warehouse and the destination, take
into account the occupational health and safety principles for manual transport operations which apply
in the country where the hydraulic will be used.
25. Do not operate if tired or intoxicated.
26. The surface under the press should be dry and level. It should be stable and maintain correct balance
whilst the press is in use. Use protective non-slip boots.
27. Press operators should wear safety goggles and a face mask to protect against possible impact as well
as heavy duty protective gloves. Do not put objects or limbs close to articulated parts.
28. The device is not resistant to the negative effects of the elements.
29. Secure the load to prevent it from moving on the worktable during press operation (the work piece
should be centred).
30. Do not press items with spring like qualities (e.g. springs) or elements which could crack and/or break
under pressure or objects which could explode.
Failure to follow recommended safety instructions may result in injury or death
III. INTENDED USE OF THE MACHINE
The Hydraulic Shop Press is designed for repair and service workshops as well as industrial facilities. It is
useful for mechanics, farmsteads and other workshops etc.The press is designed for pressing (e.g. bearings),
bending and rectifying elements. The press includes an adjustable height worktable (depending on the model)
so that its height can be set at a level ideally suited for the given task.
Any damage resulting from the misuse of the device is to be paid by the user!
18
IV. TECHNICAL SPECIFICATIONS
Product name
Model
Art. No.
Pressure
Piston stroke
Width
Weight
Manometervorgaben:
Load (T)
2
4
6
8
10
12
18
20
24
30
40
50
V. BEFORE FIRST USE
Upon receipt of the goods, check the packaging for damage and open it. If the packaging is damaged, please
contact your transport company and distributor within 3 days and document the damages as detailed as
possible. Do not turn the package upside down! When transporting the package, please ensure that it is kept
horizontal and stable. The various items used for packaging (cardboard, plastic straps, polyurethane foam)
should be conserved, so that the machine can be sent back to the service center in the best condition in
case of any problems
VI. ASSEMBLING THE MACHINE
Before placing the machine in its working position, inspect it for any damage. Make sure the surface is level
and its load bearing parameters are sufficient for the weight of the machine. Users are responsible for
positioning the machine correctly. Assemble the machine with due care and observe all OHS requirements
to avoid risk of injury. Make sure the work pieces are clean and satisfy the aforementioned requirements, i.e.
not brittle, does not break or spring under loading.
Rev. 09.12.2016 Rev. 09.12.2016
Hydraulic Shop Press
MSW-WP-10T MSW-WP-30T MSW-WP-30T-P
6300 6301 6302
10 T 30 T 30 T
130 mm 160 mm 160 mm
380 mm 460 mm 460 mm
45 kg 125 kg 145 kg
MSW-WP-10T MSW-WP-30T | MSW-
WP-30T-P
Pressure
bar psi bar psi
123 1788 - -
247 3576 - -
370 5364 133 1931
493 7152 - -
617 8940 - -
- - 266 3862
- - 400 5793
- - - -
- - 533 7725
- - 666 9656
- - - -
- - - -
MSW-WP-50T-P
6303
50 T
180 mm
615 mm
241 kg
MSW-WP-50T-P
bar psi
- -
- -
- -
- -
125 1810
- -
- -
250 3621
- -
375 5431
499 7242
624 9052
19