Haier HMV1472BHS Instrucciones De Instalación página 18

INSTALL GREASE FILTERS
Grease filters are located on the underside of microwave oven. For
installation instructions, see the User Manual packed with the microwave.
a
d
METHOD B - OUTSIDE BACK EXHAUST (HORIZONTAL DUCT)
IMPORTANT:
•
Make sure the screws for the blower motor and blower plate are securely
tightened when they are reinstalled. This will help avoid excessive vibration.
•
Make sure the motor wiring has been properly routed and secured, and that
the wires are not pinched.
CREATE REAR WALL EXHAUST OPENING
1. Read the instructions on the Mounting Plate/Rear Wall template.
2. Tape the Mounting Plate/Template to the rear wall, aligning it with the holes
previously drilled for holes A and B in the mounting plate.
3. Cut the opening, following the instructions on the Rear Wall template.
REMOVE THE BLOWER PLATE
1. Remove and save the screw(s) fastening the blower plate to the microwave.
2. Lift off the blower plate.
b
c
NOT E:
IT IS VER
REA D AND FOL Y IMPO
IN THE RTA NT
INST ALLA LOW THE TO
BEF ORE DIRE CTIO
PRO CEE TION INST NS
REA R WAL L DING RUC TION
TEM PLA WIT H S
This Rear TE. THIS
moun ting Wall Temp 3/8" TO EDGE
plate and late serves
outlet. to locate to positio 12"
1. Use a level the horizo n the bottom
accura to check ntal exhau
tely. that the st
2. Locate and mark templa te is positio
right side at least ned
of the center one stud
It is impor line. on the left or 4"
screw mount tant to
of the microw ed firmly use at least one
ave. Mark in a stud wood
locatio ns for the two additio to suppo rt the weigh
3. Drill holes in suppli ed nal, evenly t
a stud, the marke toggle bolts. space d
drill a 3/16" d locatio Trim the
that do not line hole for ns. Where
toggle up with wood screw there is
bolts. a stud, drill 5/8" s. For holes
DO NOT holes for
AT THIS INSTA
4. Remo TIME. LL THE MOUN
ve the TING PLAT
5. Revie w the Install templa te from E
install ation ation Instru the rear
situati on. ction book wall.
for your
Darle vuelta
versió n a la hoja
en Españ para consu
ol. ltar la
Loca te
and mark
mou nting hole s to
plate . align with
IMPO RTA hole s in
NT: the
LOC ATE
AT LEA
THE CEN ST ONE
TER LINE STU D
MAR K . ON EITH
THE LOC ER SIDE
SPA CED ATIO N OF
TOG GLE FOR 2
ARE A. BOL TS ADD ITIO
IN THE NAL , EVE
MOU NTIN NLY
G PLA TE
Trim the
rear wall
temp late
alon g
the dott
ed line.
Loca te
and mark
mou nting hole s to
plate .
IMPO RTA
NT:
LOC ATE
AT LEA
THE CEN ST ONE
TER LINE
MAR K .
THE LOC
SPA CED ATIO N
TOG GLE
ARE A. BOL TS
rear wall
temp late
alon g
the dott
ed line.
align with
hole s in
the
STU D
ON EITH
ER SIDE
OF
FOR 2
ADD ITIO
IN THE NAL , EVE
MOU NTIN NLY
G PLA
TE
16
Surface Lights
A
Door
B
Grease Filters
C