Haier HMV1472BHS Instrucciones De Instalación página 38

Ocultar thumbs Ver también para HMV1472BHS:
Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

STYLE 2 - SOUS UN PLACARD ENCASTRÉ AVEC ENCADREMENT
IMPORTANT :
Le four à micro-ondes doit être d'aplomb. Vérifier l'aplomb du
fond du placard à l'aide d'un niveau.
1.
Tracer une ligne verticale sur le mur au centre de l'espace de 24" (61 cm) de
large.
2.
Positionner la plaque de montage/gabarit mural arrière sur le mur de sorte que
l'axe du gabarit soit aligné avec la ligne médiane et que le haut du gabarit soit en
contact avec le bas du placard. À l'aide de ruban adhésif, fixer le gabarit en
position.
NOTE :
IT IS VERY
READ
IMPO RTAN
IN THE
AND FOLL
INST ALLA
OW THE
T TO
BEFO RE
TION INST
DIRE CTIO
REAR
PRO CEED
RUC TION
NS
WAL L
ING WITH
S
This Rear
TEMP LATE
THIS
3/8" TO EDGE
mounti ng
Wall Templa
.
plate and
te serves
12"
outlet.
to locate
to position
the bottom
1. Use
a level
the horizon
tal exhaus
accura tely.
to check
that the
t
2. Locate
templa te
and mark
is position
right side
of the centerl
at least
one stud
ed
4"
It is importa
ine.
on the left
screw mounte
nt to use
or
of the microw
d firmly
at least
location
ave. Mark
in a stud
to suppor
one wood
s for the
two addition
t the weight
3. Drill holes
supplie
d toggle
al, evenly
a stud,
drill a 3/16"
in the marked
bolts.
spaced
that do
hole for
location
s. Where
toggle bolts.
not line
up with
wood screws
there is
a stud,
drill 5/8"
. For holes
DO NOT
holes for
AT THIS
INSTAL
4. Remov
TIME.
L THE MOUN
5. Review
e the templa
TING PLATE
the Installa
te from
the rear
installa tion
situatio
tion Instruc
wall.
n.
tion book
for your
Darle vuelta
versió n
a la hoja
para consu
en Españ
ol.
ltar la
Locat e
and mark
moun ting
holes to
plate.
align with
IMPO RTAN
holes in
T:
the
LOCA TE
AT LEAS
THE CENT
T ONE
ERLI NE.
STUD
ON EITH
MAR K
THE LOCA
ER SIDE
SPAC ED
TION FOR
OF
TOGG
AREA .
LE BOLT
2 ADDI
TION AL,
S IN THE
EVEN LY
MOU NTIN
G PLAT
E
Trim the
rear wall
temp late
along
the dotte
d line.
a
(41.9 cm)
a
Trim the
rear wall
temp late
along
the dotte
d line.
Loca te
and mark
moun ting
holes to
plate .
align with
IMPO RTAN
holes in
T:
the
LOCA TE
THE CENT
AT LEAS
T ONE
STUD
MAR K
ERLI NE.
ON EITH
THE LOCA
ER SIDE
SPAC ED
TION FOR
OF
TOGG
2 ADDI
AREA .
LE BOLT
TION AL,
S IN THE
EVEN LY
MOU NTIN
G PLAT
E
b
A
16½"
Ligne axiale
A
30" (76,2 cm) jusqu'à
B
la surface de cuisson
36
Ligne
axiale

Publicidad

Tabla de contenido
loading

Tabla de contenido