Standard Accessories; Prior To Operation - Metabo HPT CJ 110MV Instrucciones De Manejo

Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

English
PRECAUTIONS ON USING JIG SAW
This Jig saw employs a high-power motor. If the machine is
used continuously at low speed, an extra load is applied to
the motor which can result in motor seizure. Always operate
the power tool so that the blade is not caught by the material
during operation. Always adjust the blade speed to enable
smooth cutting.
SPECIFICATIONS
Voltage (by areas)*
Power Input*
Max. Cutting Depth
No-load speed
Stroke
Min. Cutting Radius
Weight (without cord)
* Be sure to check the nameplate on product as it is subject to change by areas.

STANDARD ACCESSORIES

(1) Blades (No. 41) ............................................................1
Refer to Table 1 for use of the blades.
(2) Hexagon bar wrench .....................................................1
(3) Splinter guard ...............................................................1
(4) Dust collector ................................................................1
(5) Chip cover .....................................................................1
Standard accessories are subject to change without notice.
OPTIONAL ACCESSORIES ... Sold separately
(1) Various types of blades
Refer to Table 1 for use of the blades.
(2) Guide
(3) Sub base
(4) Bench stand (Model TR12-B)
Optional accessories are subject to change without notice.
APPLICATIONS
○ Cutting various lumber and pocket cutting
○ Cutting mild steel plate, aluminum plate, and copper
plate
○ Cutting synthetic resins, such as phenol resin and vinyl
chloride
○ Cutting thin and soft construction materials
○ Cutting stainless steel plate (with No. 97 blade)

PRIOR TO OPERATION

1. Power source
Ensure that the power source to be utilized conforms
to the power requirements specifi ed on the product
nameplate.
2. Power switch
Ensure that the power switch is in the OFF position.
If the plug is connected to a receptacle while the power
switch is in the ON position, the power tool will start
operating immediately, which could cause a serious
accident.
5
(110 V, 115 V, 120 V, 127 V, 220 V, 230 V, 240 V)
720 W
Wood 110 mm
Mild Steel 10 mm
850 – 3000 /min
26 mm
25 mm
2.2 kg
3. Extension cord
When the work area is removed from the power source,
use an extension cord of suffi cient thickness and rated
capacity. The extension cord should be kept as short as
practicable.
4. Dust produced in operation
The dust produced in normal operation may aff ect
the operator's health. Either of following way is
recommended.
a) Wear a dust mask
b) Use external dust collection equipment
When using the external dust collection equipment,
connect the adapter with the hose from external dust
collection equipment.
5. Changing blades
(1) Open the lever up to the stop. (Fig. 1-I)
(2) Remove fi tted blade.
(3) Insert new blade up to the stop in the blade holder.
(Fig. 1-II)
(4) Close the lever. (Fig. 1-III)
CAUTION
○ Be sure to switch power OFF and disconnect the plug
from the receptacle when changing blades.
○ Do not open the lever when plunger is moving.
NOTE
○ Confi rm the protrusions of blade inserted to the blade
holder surely. (Fig. 2)
○ Confi rm the blade located between the groove of roller.
(Fig. 3)
6. Adjusting the blade operating speed
This Jig Saw is equipped with the electric control
circuit which enables stepless speed control. To adjust
the speed, turn the dial shown in Fig. 4. When the
dial is set to "1", the jig saw operates at the minimum
speed (850/min). When the dial set to "5", the jig saw
operates at the maximum speed (3000/min). Adjust the
speed according to the material to be cut and working
effi ciency.
CAUTION
At low speed (dial setting: 1 or 2) do not cut a wood with
a thickness of more than 10 mm or metal with a thickness
of more than 1 mm.

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

Cj 110mva

Tabla de contenido