JB Systems Light ILEAD CONTROLLER Manual De Instrucciones página 4

ENGLISH
FUNCTIONS
(FRONT)
1. Scanners: To select one or more fixtures.
2. Movement: To select/set the pan & tilt movement.
3. Shutter: To set the strobe speed, shaking effect and open.
4. Gobo: To select gobo.
5. Color: To select color.
6. Rotation: To set the rotation speed and direction.
7. Dimmer: To set the dimmer intensity.
8. Focus: To adjust the appropriate focus.
9. Page/ Copy: To select memory 1~12 or 13~24 or activate memory copy.
10. Memory: To edit exist scenes or delete a chase.
11. Cancel: To delete a scene.
12. Save: To save or insert or overwrite a scene.
13. Auto/Sound/Midi: To set Auto/Sound/Midi three modes.
14. Light show: To run the Light Show.
15. Blackout/Stand Alone: To select Program/Blackout/Stand Alone three modes.
16. Fog: To activate Fog Machine.
17. Strobe: To activate Non-DMX Strobe. Hold on the Strobe button and press button 1 ~ 12
separately to change the strobe speed.
18. X-Fade: Controls with two different functions:
 To set fade time when running Light shows. Fade time is the amount of time it takes for a
scanner (or scanners) to move from one position to another.
 To set the tilt position of the Scanners when programming or to set the tilt movement range for
Movement function or to set DMX value 0~255 for channels of Shutter/Gobo/
Color/Rotation/Dimmer/Focus.
19. Speed ( Wait time ) Controls with two different functions:
 To set chase speed ( wait time between scenes ) within the range of 0.1 second to 5 minutes
when running light shows. The fade time of scenes will be always completed,
decides the wait time ( interval time ) between scenes.
 To set the pan position of the Scanners or to set pan movement range for Movement function
when programming.
20. Fine: To control the pan or tilt movement of the fixture in the smallest increments. Push down the
joystick to activate Fine function, push again to disable the function.
21. Override: To override the fixture/ fixtures when the show is running.
22. Button(1-24): Set DMX value 0~255 for channels of Shutter / Gobo / color / Rotation / Dimmer /
Focus, or save 24 memories into the buttons.
23. Stand alone: 2 extra easy controllers Incorporated for Master/Slave immediate pre-programmed
light shows.
24. Program Mode: Activate Program mode by pressing Blackout/Stand Alone button. When the LED
above the button is off, it's in Program mode.
JB SYSTEMS
®
OPERATION MANUAL
Speed slider
3/71 iLEAD Controller
ENGLISH
FUNCTIONS
(rear)
1. POWER: Turns On/Off the power.
2. DC INPUT: DC 9 ~12V, 300mA min.
3. FOG MACHINE: 5 pin din socket for connecting DC Fog Machine.
Fog machine diagram
(Compatible with Antari Z800 & Z1000)
4. STROBE: Trigger non-DMX strobe. Signal +12V DC.
5. AUDIO IN: By build-in microphone or line in.
6. MIDI IN: To receive MIDI data input.
7. DMX IN: This connector accepts DMX signals input.
8. DMX OUT: Two connectors sends DMX signals to DMX fixtures, use 3 pin XLR plug cable to link
the fixture together.
9. STAND ALONE: The connectors are used only in master/slave mode, using 5 pin XLR cable
microphone jack of the first fixture, you will find that the remote control on the first unit will control all
the other units for Stand by, Function and Mode.
JB SYSTEMS
®
OPERATION MANUAL
4/71 iLEAD Controller