Panasonic SC-UX100 Manual Del Propietário página 14

SC-UX100 PP TQBJ0973 En.fm Page 14 Saturday, August 13, 2016 5:06 PM
█
Main unit displays
"ADJUST CLOCK"
•
The clock is not set. Adjust the clock.
"ADJUST TIMER"
• The play timer is not set. Adjust the play timer.
"AUTO OFF"
•
The system has not been used for 20 minutes and will turn
off within a minute. To cancel, press any button.
"ERROR"
• An incorrect operation was done. Read the instructions and
try again.
"F61"
• Examine and correct the speaker cords connection.
•
Disconnect the USB device. Turn off the system and then
turn on again.
"F703"
•
Examine the Bluetooth ® connection.
•
Disconnect the Bluetooth
®
then turn on again.
"F76"
• There is a problem with the power supply.
• Disconnect the AC power supply cord and consult your
dealer.
"F77"
• Disconnect the AC power supply cord and consult your
dealer.
"NO DISC"
•
You have not put in a disc.
"NO PLAY"
"UNSUPPORT"
•
Examine the content. You can only play supported format.
•
The system may have a problem. Turn off the system and
then turn on again.
"NO TRACK"
•
There is no album or track in the USB device.
"PLAYERROR"
•
An unsupported MP3 file has been played. The system will
skip that track and play the next one.
"REMOTE 1"
"REMOTE 2"
• The remote control and the main unit are using different
codes. Change the code of the remote control.
–
When "REMOTE 1" is shown, press and hold [OK] and
[ ] on the remote control for a minimum of 4 seconds.
–
When "REMOTE 2" is shown, press and hold [OK] and
[USB/CD] on the remote control for a minimum of
4 seconds.
14
Confidential
Until: 9 Jan 2017
device. Turn off the system and
digital printing
"TEMP NG"
•
The temperature protection circuit has been activated, and
the system will turn off. Let the unit cool down before
turning it on again.
•
Check that the ventilation opening of the unit is not
obstructed.
•
Ensure this unit is well ventilated.
"USB NO DEVICE"
• The USB device is not connected. Examine the connection.
"USB OVER CURRENT ERROR"
•
The USB device is using too much power. Disconnect the
USB device, turn off the system and then turn on again.
"VBR"
• The system cannot show the remaining play time for
variable bit rate (VBR) tracks.
Remote control code
When other Panasonic equipment responds to the
remote control of this system, change the remote control
code for this system.
Preparation
Press [USB/CD] to select "CD".
█
To set the code to "REMOTE 2"
1
Press and hold [USB/CD] on the main unit and
[USB/CD] on the remote control until "REMOTE 2"
is shown.
2
Press and hold [OK] and [USB/CD] on the remote
control for a minimum of 4 seconds.
█
To set the code to "REMOTE 1"
1
Press and hold [USB/CD] on the main unit and [
on the remote control until "REMOTE 1" is shown.
2
Press and hold [OK] and [
control for a minimum of 4 seconds.
System memory reset
Reset the memory when the following situations occur:
• There is no response when buttons are pressed.
• You want to clear and reset the memory contents.
1
Disconnect the AC power supply cord.
2
While you press and hold [1] on the main unit,
connect the AC power supply cord again.
Continue to press and hold the button until
"– – – – – – – – –" is shown.
3
Release [1].
All the settings are set back to the factory preset.
It is necessary to set the memory items again.
]
] on the remote