Preparations For Installation - aldes Dee Fly Instrucciones De Montaje

PrEParatiOns FOr installatiOn

installation precautions for flexible, insulated ducts:
• Ensure the network is sealed around the sleeves and connectors by using fixing collars.
• Avoid unnecessary bends.
• Stretch the duct out into straight lines.
• Do not crush ducts, and make sure they are visible so no one else will crush them Dee Fly assembly
Connectors
the motor and heat exchanger casings are equipped with 4 Ø160 mm connectors.
Fresh air intake Air supply
Exhaust to outside Air extract
To avoid the nuisance of noise transmission, it is imperative that
connections to the motor casing use flexible couplings: flexible sleeves
or ducts.
For maintenance or replacement access to equipment, there must be
hatches that are large enough to permit access to the equipment or the
technical area
To facilitate the mounting of circular flexible ducts and to ensure that
the network is sealed, each connector is fitted with a 160 mm diameter
quick-fit connector. Insulated ducts must be used once the ducts are in
a non-heated volume (for assembly instructions, see page 30)
Attach the insulator and the outer duct
Attach the inner duct to
and tighten it with the fixing collar
the connector using
Make sure the duct is properly fitted
a collar.
and sealed.
22
YouR NEEDS DEPENDING oN tHE DWELLING
(According to the French Building Regulation. Refer to the local Building Regulation to select the airflow.)
Airflow Airflow Airflow Airflow
kitchen Bath 1 Bath 2 Bath 3
cellar m
m /h m /h m /h m /h
3 3 3 3
45 30
Basic airflow
105 30
Kitchen airflow
Basic airflow 45 30
Kitchen airflow 135 30
3-room
dwelling
45 30
Basic airflow
135 30
Kitchen airflow
45 30 30
Basic airflow
135 30 30
Kitchen airflow
45 30
Basic airflow
135 30
Kitchen airflow
45 30
Basic airflow
135 30
Kitchen airflow
4-room
dwelling
Basic airflow 45 30 30
Kitchen airflow 135 30 30
45 30 30
Basic airflow
135 30 30
Kitchen airflow
Basic airflow 45 30
Kitchen airflow 135 30
45 30
Basic airflow
135 30
Kitchen airflow
Basic airflow 45 30 30
Kitchen airflow 135 30 30
5 and
more Basic airflow 45 30 30
room Kitchen airflow 135 30 30
dwelling
Basic airflow 45 30 30 30
Kitchen airflow 135 30 30 30
Basic airflow 45 30 30 30
Kitchen airflow 135 30 30 30
Basic airflow 45 30 30 30
Kitchen airflow 135 30 30 30
FLOW RATE SELECTION
(Only for the Dee Fly high efficiency version)
The choice of air flow rate is dependant on the number
of 'wet rooms' – shown in the table above.
The selection is made be a switch on the back
of the Dee Fly controls. Simply position the jumpers as
shown below to obtain
the required basic
airflow rate:
Exhaust
Total
Airflow Airflow Airflow Airflow
Airflow SWITCH
exhaust
WC1 WC2 WC3 dressing
/h Position
3 airflow
m /h m /h m /h m /h
3 3 3 3
m 3 /h
15 90
15 150
1 2
15 15 105
15 15 195
1 2
15 15 15 120
15 15 15 210
1 2
15 15 135
15 15 225
1 2
30 105
30 195
1 2
15 15 15 120
15 15 15 210
1 2
15 15 135
15 15 225
1 2
15 15 15 150
15 15 15 240
1 2
30 105
30 195
1 2
15 15 15 120
15 15 15 210
1 2
15 15 135
15 15 225
1 2
15 15 15 150
15 15 15 240
1 2
15 15 165
15 15 255
1 2
15 15 15 180
15 15 15 270
1 2
15 15 15 15 195
15 15 15 15 285
1 2
90 m 3 150 m 3
1 2 3 4 1 2
105 m 3 165 m 3
1 2 3 4 1 2
120 m 3 180 m 3
1 2 3 4 1 2
135 m 195 m
3 3
1 2 3 4 1 2
23
Supply
N° of
grilles
3 4
4
3 4
3 4
3 4
5
3 4
3 4
3 4
6
3 4
3 4
3 4
3 4
T5=6
T6=7
3 4
T7=8
3 4
3 4
3 4
3 4
3 4
3 4
3 4