Hoshizaki KMD-201AA Manual De Instrucciones página 4

* A vented tee connection is required for proper drain flow. See Fig. 5.
* The icemaker drain line must be run separately from the storage
bin/dispenser unit drain line. See Fig. 5.
* There should be no backflow in the water circuit.
* Water supply connection is intended to be made by means of a
pipe, not a hose set.
Note: Jointing compounds should be approved and suitable for
potable water use.
Icemaker
Water Supply Inlet
Icemaker
/2"FPT
Icemaker
Drain Outlet
3/4"FPT
Bin
II. OPERATING INSTRUCTIONS
. This icemaker is designed to produce edible ice. To keep
the icemaker hygienic:
* Wash your hands before removing ice. Use the Plastic
Scoop provided (accessory).
* The Storage Bin is for ice use only. Do not store anything
else in the Bin.
* Clean the Storage Bin before use (see "III. . CLEANING").
* Keep the Scoop clean. Clean it by using a neutral cleaner
and rinse thoroughly.
* Close the Door after removing ice to prevent entrance of
dirt, dust or insects into the Storage Bin.
2. The use of any electrical equipment involves the observance
of some fundamental rules. In particular:
* Instances of high humidity and moisture increase the risk
of electrical short circuits and potential electrical shocks. If
in doubt, disconnect the icemaker.
* Do not pull the power cord in order to disconnect the
icemaker from the feed network.
* This appliance is not suitable for unsupervised use by
young children or aged or infirm persons.
3. All parts are factory-adjusted. Improper adjustments may
result in failure.
4. If the unit is turned off, wait for at least 3 minutes before
r e s t a r t i n g t h e i c e m a k e r t o p r e v e n t d a m a g e t o t h e
Compressor.
Icemaker
Water Supply Line
Shut-Off Valve
Icemaker
Water Supply Line
Drain Valve
Bin Drain Outlet
3/4"FPT
Separate piping to approved
drain. Leave a two-inch (5cm)
vertical air gap between the
end of each pipe and the drain.
two-inch (5cm)
air gap
Floor
Drain
Fig. 5
WARNING
1. OPERATION
The installer will normally commission the icemaker to start the
automatic icemaking process. To ensure continuous operation, make
sure that:
* The water supply tap is on,
* The icemaker is plugged into the power supply, and
* The Control Switch is in the "ICE" position.
2. PREPARING THE ICEMAKER FOR LONG STORAGE
) Move the Control Switch to the "OFF" position.
2) Unplug the icemaker or disconnect the power supply.
3) Close the water supply tap, and remove the Inlet Hose.
4) Remove all ice from the Storage Bin/Dispenser, and clean the Bin/
Dispenser.
5) Ask for draining of the icemaker by professional qualified
personnel.
III. MAINTENANCE
1. CLEANING
. Before carrying out any cleaning or maintenance operations,
unplug the icemaker from the electrical supply network.
2. Ask a trained service person to clean and sanitise the
icemaker water system at least twice a year and to check
and clean the Condenser at least once a year.
3. This appliance must not be cleaned by use of a water jet.
4. Do not use any alcohol for cleaning/sanitisation of the
icemaker. It may cause cracks on the plastic parts.
[1] Machine and Bin Exterior
Wipe the exterior at least once per week with a clean, soft cloth. Use
a damp cloth containing a neutral cleaner to wipe off grease or dirt.
[2] Scoop
) Either mix 3 litres of water with  ml of 5.25% sodium hypochlorite
solution in a suitable container, or the recommended Hoshizaki
sanitiser as directed.
2) Soak the Scoop in the solution for more than 3 minutes. Rinse
thoroughly, and shake to remove surplus liquid.
Note: Using a cloth to dry may re-contaminate.
[3] Storage Bin Interior Cleaning/Sanitisation (Weekly)
) Open the Storage Bin Door, and remove all ice.
Note: Hoshizaki recommends various types of Storage Bin for
the icemaker which vary in size and design. The following
instructions are therefore for general guidance only.
2) Wash the Bin liner and Door inner surface with a neutral non-
abrasive cleaner. Rinse thoroughly with a clean cloth and fresh
water.
3) Either mix 5 litres of water with 8 ml of 5.25% sodium hypochlorite
solution in a suitable container or the recommended Hoshizaki
sanitiser as directed.
4) Soak a clean sponge or cloth with the solution, and wipe the Bin
liner and Door inner surface.
3
ENGLISH
WARNING