Nussbaum POWER LIFT HF 3S 5000 Instrucciones De Servicio página 106

Regular safety inspection and maintenance
i Copy, complete and leave in the inspection book
Test step
Model plate .......................................................
Brief operating instructions on the column ....
Operating manual ............................................
Load capacity details on the system .............
Condition / function operating lever and button
Condition / function of CE stop and warning signal
Function button "LIFT, LOWER" ........................
Condition, lockable main switch ....................
General system condition ................................
Condition of covers ............................................
Check the play of sliding parts on the lift columns
Condition/ function lifting arm ........................
Condition/ function lifting arm block .............
Condition/ function lifting arm movement ............
Condition/ function carrier plate / support parts
Condition / function of foot bumper (optional)
Condition/ function latch ................................
Securing the lifting arm bolts ...........................
Load bearing construction (deformations, cracks)
Condition, function riser extension ..................
Condition of cross-beam ................................
Condition of concrete floor (cracks) ..............
Fastening anchor torque .................................
Fastening screw torque ....................................
Condition, hydraulic unit .................................
Paint condition ..................................................
Cylinder condition ............................................
Condition wiper cylinder ..................................
Hydraulic system leak-tightness .......................
Hydraulic oil filling level .....................................
Condition of hydraulic lines incl. screw fittings
Functional test "overflows" ..............................
Condition electrical lines ..................................
Condition / function energy set (optional) ....
Condition of weld seams ................................
Functional test, system with load ....................
*) Place a checkmark in the relevant, if a retest is required then check it again!
Safety inspection done on:
Performed by company:
Name, address of specialist:
Result of inspection:
______________________________
Signature of specialist
If requested to take care of deficiencies
Deficiency removed on:
(Use a new form for reinspection!)
106
Serial number: _________________________________
OK Defect
missing
□ □
................. ................
□ □
................. ................
□ □
................. ................
□ □
................. ................
□ □
................. ................
□ □
................. ................
□ □
................. ................
□ □
................. ................
□ □
................. ................
□ □
................. ................
□ □
................. ................
□ □
................. ................
□ □
................. ................
□ □
................. ................
□ □
................. ................
□ □
................. ................
□ □
................. ................
□ □
................. ................
□ □
................. ................
□ □
................. ................
□ □
................. ................
□ □
................. ................
□ □
................. ................
□ □
................. ................
□ □
................. ................
□ □
................. ................
□ □
................. ................
□ □
................. ................
□ □
................. ................
□ □
................. ................
□ □
................. ................
□ □
................. ................
□ □
................. ................
□ □
................. ................
□ □
................. ................
□ □
................. ................
_________________________________________________________________
_________________________________________________________________
_________________________________________________________________
□
Continued operation questionable, reinspection required
□
Continued operation possible, remove defects by ___________________
□
No deficiencies, continue to operate
______________________________
Operating company signature
______________________________
OPI-POWER LIFT HF 3S 5000 - HYMAX HF 3S 5000-V1.1-DE-EN-FR-ES-IT
Reinspect Remarks
□
_______________________________
□
_______________________________
□
_______________________________
□
_______________________________
□
_______________________________
□
_______________________________
□
_______________________________
□
_______________________________
□
_______________________________
□
_______________________________
□
_______________________________
□
_______________________________
□
_______________________________
□
_______________________________
□
_______________________________
□
_______________________________
□
_______________________________
□
_______________________________
□
_______________________________
□
_______________________________
□
_______________________________
□
_______________________________
□
_______________________________
□
_______________________________
□
_______________________________
□
_______________________________
□
_______________________________
□
_______________________________
□
_______________________________
□
_______________________________
□
_______________________________
□
_______________________________
□
_______________________________
□
_______________________________
□
_______________________________
□
_______________________________
______________________________
Operating company signature