Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
Operating a digital satellite receiver
2 To switch the output of the
digital satellite receiver to the
TV. (When you connect a TV
cable or antenna to the receiver,
the output switches between a
TV and SAT program.)
3, 4 and qd
To change the channel. For
example, to change to channel
5, press 0 and 5 (or press 5 and
ENTER).
8 To turn on the display.
9 To bring up the Master Guide.
q; To exit the mode.
qf To call up the DISH menu.
qg Channel up: +
Channel down: –
qh To tune to the last tuned
station.
qj To call up the PVR menu.
qk To call up the MENU display.
ql To move the cursor upward,
downward, to the left, to the
right, or to enter the selection.
w; To bring up the Station Index.
Operating a DVD
2 To change the input mode.
3 and qd
Number buttons : To set items
selected from the screen.
4 To select numbers 10 and
above.
8 To show the current play status
on the screen.
9 To bring up the Master Guide.
q; To return to the previous
screen.
qd To enter the setting. To set
items selected from the screen.
qf To switch the subtitle.
qg CH+: Channel up.
CH–: Channel down.
qh To select a deck.
qj To switch the subtitle.
qk To display the DVD menu.
wa N:
To play.
m:
To rewind.
To fast-forward.
M:
zREC: To record, press N
while pressing zREC.
x:
To stop.
X:
To pause.
.: To proceed to the
previous location.
>:
To proceed to the next
location.
:
Replay
:
Advance
ws A: RED button
B: GREEN button
C: YELLOW button
D: BLUE button
wd PAGE+: Page up.
PAGE-: Page down.
wf To call up the title of the
recorded program.
wg To use the "FAVORITE"
function.
ql To move the cursor upward,
downward, to the left, to the
right, or to enter the selection.
w; To call up the "TOOLS" menu.
wa N:
To play.
m:
To rewind.
To fast-forward.
M:
zREC: To record, press N
while pressing zREC.
To stop.
x:
X:
To pause.
.: To proceed to the
previous location.
>:
To proceed to the next
location.
:
To operate " Flash –."
:
To operate " Flash +."
ws B: open/ close
D: To display the Top Menu.
A: To call up the setup menu.
wd PAGE+: To select DVD deck.
PAGE-: To select HDD deck.
wf To display the title menu.
Operating a DVD Home Theater
2 To change the input mode.
3 and qd
Number buttons: To set items
selected on the screen.
4 To select numbers 10 and
above.
6 VOL+: AMP volume up
VOL–: AMP volume down
7 AMP volume muting
8 To show the current play status
on the screen.
9 To change the sound.
q; To return to the previous
screen.
qf To switch the subtitle.
qg CH+: Tuner +
CH–: Tuner –
qk To call up the MENU.
ql To move the cursor upward,
downward, to the left, to the
right, or to enter the selection.
w; AMP menu
Specifications
Operable distance
Approx. 7 m (23 ft) (varies depending of the
component of each manufacturer)
Power requirements
Two size AA (R6) batteries (not supplied)
Battery life
Approx. 1 year (varies depending on frequency of
button use - up to approx. 300 times per day.)
Dimensions
Approx. 53 × 220 × 29 mm (w/h/d)
× 8
(2
/
1
3
8
Mass
Approx. 108 g (3.8 oz.) (not including batteries)
Design and specifications are subject to change without notice.
The validity of the CE marking is restricted to only those countries
where it is legally enforced, mainly in the countries EEA (European
Economic Area).
Troubleshooting
If you have problems setting up or using the Commander:
• When setting up the Commander, carefully go through the procedures
described in "Setting the Code." If the code that's listed first for your
component doesn't work, try all the codes for your component - in the order
in which they're listed. If all the codes fail to work (or if your component is
not listed in this manual), try using the procedures in "Searching for the
Correct Code."
• Check that you're aiming the Commander directly at the component, and that
there are no obstructions between the Commander and the component.
• Make sure the batteries you're using are not worn out, and that they're
inserted correctly.
• Check that the button of the TV, VCR, CBL, or DVD is pressed to choose your
desired component.
• Check that the component has infrared remote capability. For example, if
your component didn't come with a remote commander, it probably isn't
capable of being controlled by a remote commander.
• Should any problem persist, reset the Commander to the factory setting by
pressing the POWER, INPUT and VOL– buttons simultaneously.
For the customers in the U.S.A.
Customer Support Information
If – after you've read through this manual – you still cannot get the
Remote Commander to work properly, call the Sony Customer
Support Helpline at 1-800-822-2217.
wa N:
To play.
m:
To rewind.
To fast-forward.
M:
zREC: To record, press N
while pressing zREC.
x:
To stop.
X:
To pause.
.: To proceed to the
previous location.
>:
To proceed to the next
location.
:
To operate " Flash –."
:
To operate " Flash +."
ws B: open/ close
A: To call up the setup menu.
C: Disc skip
D: To display the Top Menu.
wg To call up MEMORY.
× 1
/
/
in.)
3
4
16
RM-V210 3-276-523-11 (1) US/ES
Publicidad
Tabla de contenido
