Maintenance And Service; Maintenance And Cleaning - Bosch GMB 32 PROFESSIONAL Instrucciones De Servicio

Ocultar thumbs Ver también para GMB 32 PROFESSIONAL:
Tabla de contenido

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 15
OBJ_BUCH-260-001.book Page 11 Wednesday, October 11, 2006 8:22 AM
Operating Instructions
For drilling, observe the operating instruc-
tions of your drill.
The magnet holding force of the drill stand
mainly depends on the thickness of the work-
piece. The thickness of the material should
not be less than 8 mm.
When drilling overhead or on surfaces that
are not horizontal, secure the drill stand with
a safety chain. In case of a power failure or exces-
sive load, the holding force of the magnet is not
maintained. The drill stand can fall down and cause
accidents.
The surface must be smooth and clean.
Smooth out coarse irregularities, e. g., weld-
ing spatter and remove loose rust, dirt and
grease. The holding force of the magnet applies
only for appropriate surfaces.
Centre-punch metal workpieces.

Maintenance and Service

Maintenance and Cleaning

Keep the drill stand clean at all times for good working
results and safe working.
If the drill stand should fail despite the care taken in
manufacturing and testing procedures, repair should
be carried out by an authorised after-sales service cen-
tre for Bosch power tools.
In all correspondence and spare parts orders, please
always include the 10-digit article number given on the
nameplate of the drill stand.
WARNING! This appliance must be earthed.
Important instructions for connecting a new
3-pin plug.
The wires in the cable are coloured according to the fol-
lowing code:
Do not connect the blue or brown wire to the earth ter-
minal of the plug.
Important: If for any reason the moulded plug is
removed from the cable of this power tool, it must be
disposed of safely.
1 609 929 K50 • 11.10.06
Service and Customer Assistance
Exploded views and information on spare parts can be
found under:
www.bosch-pt.com
Great Britain
Robert Bosch Ltd. (B.S.C.)
P.O. Box 98
Broadwater Park
North Orbital Road
Denham-Uxbridge
Middlesex UB 9 5HJ
✆ Service:. . . . . . . . . . . . . . . +44 (0) 18 95 / 83 87 82
✆ Advice line:. . . . . . . . . . . . +44 (0) 18 95 / 83 87 91
Fax: . . . . . . . . . . . . . . . . . . . . +44 (0) 18 95 / 83 87 89
Ireland
Origo Ltd.
Unit 23 Magna Drive
Magna Business Park
City West
Dublin 24
✆ Service:. . . . . . . . . . . . . . . . .+353 (0)1 / 4 66 67 00
Fax: . . . . . . . . . . . . . . . . . . . . . .+353 (0)1 / 4 66 68 88
Australia and New Zealand
Robert Bosch Australia Pty. Ltd.
RBAU/SPT
1555 Centre Road
P.O. Box 66
3168 Clayton/Victoria
✆ . . . . . . . . . . . . . . . . . . . . . +61 (0)1 / 3 00 30 70 44
Fax: . . . . . . . . . . . . . . . . . . . . +61 (0)1 / 3 00 30 70 45
www.bosch.com.au
Disposal
The drill stand, accessories and packaging should be
sorted for environmental-friendly recycling.
Subject to change without notice.
English | 11

Publicidad

Tabla de contenido
loading

Tabla de contenido