Important Safety Instructions - Master DF 20 P Manual De Instrucciones

GB

IMPORTANT SAFETY INSTRUCTIONS

CAUTION: Read and follow all instructions before operating
this fan.
Use the fan only as described in this manual. Misuse may cause a
fire or an electrical shock.
1. Make sure the power supply cable has not been damaged. If the
supply cord is damaged, it must be replaced by the
manufacturer, its service agent or similarly qualified persons in
order to avoid a hazard.
parameters of power
requirements specified on the rating plate.
2. Close supervision is necessary when this fan is used near
children, the elderly and pets.
3. Always turn the fan off after use, before cleaning, or moving
location.
4. Do not insert fingers or other objects into the fan guard.
5. Do not operate the fan in areas where petrol, paint or other
flammable liquids are used or stored.
6. Do not place the fan near an open flame, cooking or heating
appliance, or hot surface.
7. This fan is not intended for use in wet or damp locations.
Never locate the fan in an area where it may fall into a bath or
other water container.
8. Always use on a dry, level surface.
9. Do not let the power cord hang over the edge of a table or
counter.
10. Arrange the cord away from an area where it may be tripped
over.
11. Never place the power cord under a carpet or rug.
12. To disconnect from the power supply, grip the plug and pull from
the power socket. Never pull by the cord.
13. This fan should not be operated outside.
14. Do not operate without fan guard properly in place.
15. Do not cover the fan during operation.
16. Do not leave the unit unsupervised during operation.
OPERATING INSTRUCTION
To adjust airflow upward or downward: Tilt the fan head to the desired
angle by hand easily
Speed Control: Rotate SWITCH to LOW, MEDIUM or HIGH speeds
for respective air velocity.
1. After continuous operation, it is normal for the motor to feel warm
when touched.
2. This fan features an overheat safety cut-out device, which will
automatically shut the fan off should it overheat for any reason. If
this happens immediately unplug the fan from the power socket.
Moreover, check if the technical
supply source comply with
MAINTENANCE
1. Before cleaning turn the fan off and unplug from the power supply.
2. To clean the fan use a soft cloth to wipe off any dust. If the fan is
very dirty use a damp cloth and wipe dry. Do not use any cleaning
detergents, sprays or other chemicals, as they will damage the
plastic.
3. Store the fan in the original packaging in a ventilated dry area.
4. The motor bearings are permanently sealed and do not require
additional lubrication.
WANRING
Do not operate the fan with a damaged cord or plug, after the fan
malfunctions, has been dropped or damaged.
the Do not use extension cords with this product!
To reduce the risk of fire or electrical shock, do not use the product
with a solid state speed control device.
Caution:
Automatically operated device-To reduce the risk of injury disconnect
from power supply before servicing.
This appliance is not intended for use by persons
(including children) with reduced physical, sensory or
mental capabilities, or lack of experience and knowledge,
unless they have been given supervision or instruction
concerning use of the appliance by a person responsible
for their safety. Children should be supervised to ensure
that they do not play with the appliance.
1
1. Use the supplied mounting accessory (5) to install the drum fan at
the wall. Or use other appropriate screws and dowel pins
corresponding to the mounting surface.
2. Hang the fan, as pictured, on two installed mounting brackets (9).
Screw the securing screws onto the mounting brackets .
3. Additionally attach the securing cable (4) to the wall.
Ceiling Mounting Fig 2
1. Use the supplied mounting accessory (5) to install the drum fan at
the ceiling. Or use other appropriate screws and dowel pins in
corresponding to the surface of the ceiling.
2. Hang the fan, as pictured, on three installed mounting brackets (9).
Screw the securing screws onto the mounting brackets.
3. Additionally attach the securing cable (4) to the ceiling.
Operation fig 3
Turn the switch (6) in the position as follows:
1. Start to run the fan.
2. Fan runs faster
3. Fan runs on the fastes stage
Rotate the fan by the rotation axis (1) and / or tilt it by the tilt axis (2)
to the desired working angle. This way you can position the fan by
o
360 .
Disconnect the plug from the power mains when cleaning the unit or
when the unit is not in use for a longer period time
12
Wall Mounting Fig