KIKKA BOO 4IN1 Instrucciones De Uso página 10

Step 1: As shown in figure 1, push the setting knob and adjust the angle of seat to the level 4
Step 2: As shown in figure 2, placing the safety car seat rearward in the car sea make it cling to car seat back.
Step 3: As shown in figure 3, the car safety belt passes through the hole of the safety seat according to the blue direction. Put the car safety bell tongue into
the car buckle. Pull horizontal car belt tight and place oblique car bell into locking device, then pull belt tight again. Next, put oblique car bell into guiding
slot for Group 0+ and put remainder belt into seat belt retractor. Finally, shake the safety seat to ensure whether car seat is already fixed.
4. GROUP 1 INSTALLATION
ATTENTION:
1. The installation for Group I is forward facing and is applied to children from 9 to 18kg.
2. This car seat for Group I has three sitting postures and they are level 1/2/3.
3. After adjusting, make baby car seat cling to car seat back and strain safety belt.
4.1. UNIVERSAL I (9-18kg): 3-POINT BELT
Step 1: As shown in figure 1, push the setting knob and adjust the angle of seat to the right level.
Step 2: As shown in figure 2, place the safety car seat forward in the car seat and make it cling to car seat back.
Step 3: As shown in figure 3, the car safety belt passes through the hole of the safety seat according to the red direction. Put the car safety belt tongue into
the car buckle. Place horizontal car belt into limit hook tightly and place oblique car belt into Group 1 guiding slot, then pull belt tight again, put remainder
belt into seat belt retractor. Finally, shake the safety seat to ensure it is already fixed.
4.2. SEMI-UNIVERSAL I (9-18kg): ISOFIX + 3-POINT BELT
Step 1: As shown in figure 1, push the setting knob and adjust the angle of seat to the right level.
Step 2: As shown in figure 2, rotate ISOFIX connector outward, if you want to return the connector, you can rotate it back.
Step 3: As shown in figure 3, before inserting the two ISOFIX connectors firmly into the ISOFIX fixed point in the car seat, ISOFIX indication window will show
red sign. Then, insert the two ISOFIX connectors firmly into the ISOFIX fixed point in the car seat with a clicking noise on both side. In the meantime, ISOFIX
indication window will become green. In order to release ISOFIX connectors, push the white button and pull the ISOFIX releasing button, the indication
window will become red.
Step 4: As shown in figure 4, the car safety belt passes through the hole of the safety seat according to the red direction. Put the car safety belt tongue into
the car buckle. Place horizontal car belt into limit hook tightly and place oblique car belt into Group 1 guiding slot, then pull belt tight again, put remainder
belt into seat belt retractor. Finally, shake the safety seat to ensure it is already fixed.
5. GROUP 0+1: 5-POINT HARNESS
5.1. GROUP 0+1: 5-POINT HARNESS INSTALLATION
Step 1: Press the central adjuster and meanwhile, pull out the harness strap to release shoulder belt.
Step 2: Press the red button to open the harness buckle.
Step 3: Pull out both of the shoulder belts to both sides of the child safety seat.
Step 4: Place your child into seat and make sure the lap belt can restrict the position of pelvis. Please check the height of shoulder belts. It is better to make
shoulder belts be a little bit higher than child's shoulders.
Step 5: Pull harness adjustment strap outward to fix child and avoid harness strap to constrict child too much. Adult palm can insert between harness strap
and child's chest. Make sure the tightness is comfortable for your child and ensure the lap belt restrict the position of pelvis.
Methods to use harness buckle: Guide the two buckle latches together and engage them before putting them into the harness buckle, this should make a
click nose. The buckle latches will be released if you press the red button.
Step 6: Non-rethread harness system adjustable with headrest: according to different height of children, there are 8 levels to adjust the height of headrest
and shoulder belt in Group O+1 . There are 5 levels to adjust the height of headrest and shoulder belt in Group 2+3. Before adjustment, please loosen
5-point safety belt. Attention: after sitting, adjust the headrest to the right position.
Attention: One or two fingers is the best distance from the bottom of headrest to child's shoulders.
Step 7: If the red line in the side of headrest exceeds the height of side car seat body, you should use Group 2+3 installation.
5.2. GROUP 0+1: 5-POINT HARNESS REMOVAL
Step 1: Adjust the baby car seat to level 1.
Step 2: Push central adjuster and loosen the belt. Then, adjust headrest to level 3 or level 4 or level 5.
Step 3: Separate the shoulder belt with strap yoke: Put strap yoke into the rear cover and draw out the belt forward. Step 4: Separate shoulder pads with belt:
Draw out shoulder pads firstly, open the shoulder pads and separate shoulder belts with strap yoke, then draw out the shoulder pads.
Step 5: Open harness buckle, put the buckle pad and cushion aside.
Step 6: Separate harness buckle and car seat (see 1 and 2 ).
Step 7: Separate the strap with the seat: Separate strap yoke from the seat by hands or small tools. Then draw out the belt and fix the strap yoke with the
strap according to picture 1-2-3-4-5.
Step 8: Close the rear cover, finish the removal of the 5-point safety belt like pictures.
ENGLISH