Makita HG5030 Manual De Instrucciones página 4

Dress properly. Do not wear loose clothing or
Q
jewellery. Keep your hair, clothing and gloves
away from moving parts. Loose clothes, jewel-
lery or long hair can be caught in moving parts.
If devices are provided for the connection of
Q
dust extraction and collection facilities, ensure
these are connected and properly used. Use of
these devices can reduce dust related hazards.
Power tool use and care
Do not force the power tool. Use the correct
Q
power tool for your application. The correct
power tool will do the job better and safer at the
rate of which it was designed.
Do not use the power tool if the switch does
Q
not turn it on and off. Any power tool that cannot
be controlled with the switch is dangerous and
must be repaired.
Disconnect the plug from the power source
Q
before making any adjustments, changing
accessories, or storing power tools. Such pre-
ventive safety measures reduce the risk of starting
the power tool accidentally.
Store idle power tool out of the reach of chil-
Q
dren and do not allow persons unfamiliar with
the power tool of these instructions to operate
the power tool. Power tools are dangerous in the
hands of untrained users.
Maintain power tools. Check for misalignment
Q
or sticking of moving parts, breakage of parts
and other condition that may affect the power
tool's operation. If damaged, have the power tool
repaired before use. Many accidents are caused
by poorly maintained power tools.
Keep cutting tools sharp and clean. Properly
Q
maintained cutting tools with cutting edges are
less likely to stick and are easier to control.
Use the power tool, accessories and tool bits
Q
etc., in accordance with these instructions and
in the manner intended for the particular type
of power tool, taking into account the working
conditions and the work to be performed. Use
of the power tool for operations different from
intended could lead to a hazardous situation.
Service
Have your power tool serviced by qualified
Q
repair person using only identical replacement
parts. This will ensure that the safety of the power
tool is maintained.
ADDITIONAL SAFETY
INSTRUCTIONS FOR HEAT GUN
This appliance is not intended for use by per-
Q
sons (including children) with reduced phys-
ical,sensory or mental capabilities, or lack of
experience and knowledge.
Children should be supervised to ensure that
they do not play with the appliance.
A fire may result if the appliance is not used
Q
with care, therefore
– be careful when using the appliance
in places where there are combustible
materials;
– do not apply to the same place for a long
time;
– do not use in presence of an explosive
atmosphere;
– be aware that heat may be conducted
to combustible materials that are out of
sight;
– place the appliance on its stand after use
and allow it to cool down before storage;
– do not leave the appliance unattended
when it is switched on.
Do not place your hand over the air vents or
Q
block the vents in any way.
The nozzle and accessories of this tool
Q
become extremely hot during use. Let these
parts cool down before touching.
Always switch the tool off before putting it
Q
down.
Do not leave the tool unattended while it is
Q
switched on.
A fire may arise if the appliance is not used
Q
with care.
Heat may be conducted to combustible mate-
Q
rials that are out of sight. Do not use in a damp
atmosphere, where flammable gases may be
present or near combustible materials.
Allow the tool to cool fully before storing.
Q
Ensure adequate ventilation as toxic fumes
Q
may be produced.
Do not use as a hairdryer.
Q
Do not obstruct either the air intake or noz-
Q
zle outlet, as this may cause excessive heat
build-up resulting in damage to the tool.
Do not direct the hot air blast at other people.
Q
Do not touch the metal nozzle as it becomes
Q
very hot during use and remains hot for up to
30 minutes after use.
Do not place the nozzle against anything while
Q
using or immediately after use.
Do not poke anything down the nozzle as
Q
it could give you an electric shock. Do not
look down the nozzle while the unit is work-
ing because of the high temperature being
produced.
Do not allow paint to adhere to the nozzle or
Q
scraper as it could ignite after some time.
Removing paint
Do not use this tool to remove paint containing
Q
lead. The peelings, residue and vapors of paint
may contain lead, which is poisonous. Any
pre-1960 building may have been painted in
the past with paint containing lead and cov-
ered with additional layers of paint.
Once deposited on surfaces, hand to mouth
contact can result in the ingestion of lead.
Exposure even to low levels of lead can cause
irreversible damage to the brain and nervous
system. Young and unborn children are partic-
ularly vulnerable.
When removing paint, ensure that the work
Q
area is enclosed. Preferably wear a dust mask.
Do not burn the paint. Use the scraper and
Q
keep the nozzle at least 25 mm away from the
4 English