Festool CMS-PS 200 Manual De Instrucciones página 10

GB
The speci¿ ed illustrations can be found at the
beginning of the operating instructions.
Pictograms
Note, Danger!
Manual, read the instructions.
1 Scope of delivery
• Retaining panel for jig saw (1.1)
2 Technical data CMS-PS 200/PS 300
Weight 3.3 kg
Saw blade, maximum permissible length of
teeth:
• Wood: 105 mm
• Aluminium, steel: 60 mm
3 Intended use
The following jig saws can be ¿ tted to the
retaining panel (1.1):
• PS 200 E
• PS 2 E
• PS 2
• PS 300 Q
• PS 300 EQ
• PSB 300 Q
• PSB 300 EQ
• PS 400 EBQ
• PSB 400 EBQ
The installation of other compass saws
is not possible and therefore not per-
mitted.
Fitting one of the above-mentioned jig saws
to the retaining panel and installing it in the
CMS-GE/Basis Plus forms a mobile bench-
saw.
These machines are intended to be used for
sawing woodand wood-like materials.
With the special saw blades offered by Fes-
tool, also plastics, steels, aluminium, non-
ferrous metals and ceramic tilescan be cut.
documents for the individual materials.
The user is liable for damage and injury
result ing from incorrect usage!
4 Safety instructions
WARNING Read all safety warnings
and all instructions provided with
the working stand and the power tool to
be mounted. Failure to follow the warnings
and instructions may result in electric shock,
¿ re and/or serious injury.
Save all warnings and instructions for
future reference.
The term "power tool" in the warnings refers
to your mains-operated (corded) power tool
or battery-operated (cordless) power tool.
10
• Disconnect the plug from the power
source and/or the battery pack from
the power tool before making any
adjustments or changing accessories.
Accidental starting of the power tool is a
cause of some accidents.
• Properly assemble the working stand
before mounting the tool. Proper as-
sembly is important to prevent risk of col-
lapse.
• Securely fasten the power tool to the
working stand before use. Power tool
shifting on the working stand can cause loss
of control.
• Place the working stand on a solid,
À at and level surface. When the working
stand can shift or rock, the power tool or
workpiece cannot be steadily and safely
controlled.
• Do not overload the working stand or
use as ladder or scaffolding. Overloading
or standing on the working stand causes
the stand to be "top-heavy" and likely to
tip over.
• Prior to initial operation, the jig saw blade
must be checked for secure seating and
smooth running.
• Always use a push stick when making longi-
tudinal cuts in workpieces that are narrower
than 120 mm.
• Secure round timber on either side of the
saw blade to prevent it from turning.
• Never work with a damaged jig saw.
• Avoid overloading the jig saw.
• Before transporting the machine, remove
the jig saw blade.
• Wear suitable protection such as ear protec-
tion, safety goggles, a dust mask for work
which generates dust, and protective gloves
when working with raw materials and when
changing tools.
5 Fitting
Always remove the power supply plug
from the socket before carrying out any
work on the machine.
5.1 Preparing the jigsaw
PS 200 E, PS 2 E, PS 2:
A covering plate can be installed in the saw
bench before installing. This improves dust
extraction.
1) Push splinter protector (2.2) forward,
2) Insert cover plate (2.4, order no. 444 356)
with the side tongues (2.3) in the recesses
(2.1) of the saw bench,
3) Push cover plate right back,
4) Push splinter protector back against the
saw blade.
PS/PSB 300 Q, PS/PSB 300 EQ
A covering plate can be installed in the saw