D- 42327 Wuppertal; Fax: +49(0)202 / 787 - 2217; Din En 1127; Nico Kowalski, Walther Spritz- Und Lackiersysteme Gmbh, Kärntner Str - Walther PILOT PREMIUM Instrucciones De Servicio

Table of contents
Exploded Drawing
Declaration of CE-Conformity
Spare parts list
1 General
1.1 Model identification
1.2 Intended use
1.3 Inappropriate use
2 Technical description
3 Safety instructions
3.1 Identification of safety instructions
3.2 General Safety instructions
4 Assembly
4.1 Supply line connection
5 Operation
5.1 Start-up and shut-down
6 Spray pattern adjustments
6.1 Correcting spray pattern flaws
7 Troubleshooting and fault rectification
8 Conversion and repair
9 Cleaning and maintenance
9.1 Basic cleaning
9.2 Routine cleaning
10 Disposal
11 Technical data
2
25
26
31
31
31
32
32
33
33
33
34
34
35
35
36
37
37
38
39
39
40
40
41
24
Declaration of CE-Conformity
We, the manufacturers of the equipment, hereby declare under our sole responsibility that
the product(s) described below conform to the essential safety requirements. This declaration will
be rendered invalid if any changes are made to the equipment without prior consultation with us.
Manufacturer WALTHER Spritz- und Lackiersysteme GmbH
Kärntner Str. 18 - 30
D - 42327 Wuppertal
Tel.: +49(0)202 / 787 - 0

Fax: +49(0)202 / 787 - 2217

www.walther-pilot.de • e-mail: info@walther-pilot.de
Type Designation Manual Spray Guns PILOT PREMIUM
PILOT Premium
PILOT Premium
PILOT Premium- HVLP
PILOT Premium- HVLP
PILOT Premium- HVLP
PILOT Premium- HVLP
PILOT Premium-
PILOT Premium-
PILOT Premium- HVLP-
PILOT Premium- HVLP-
Intended purpose Processing of sprayable media
Applied Standards and Directives
EU-Mechanical Engineering Directives 2006 / 42 / EC
94 / 9 EC (ATEX Directives)
EN ISO 12100-1
EN ISO 12100-2

DIN EN 1127-1

Specification according 94 / 9 / EC
Category 2 Part marking
Authorized with the compilation of the technical file:

Nico Kowalski, WALTHER Spritz- und Lackiersysteme GmbH, Kärntner Str. 18 - 30

D- 42327 Wuppertal

Special remarks :
The named product is intended for installation in other equipment. Commissioning is prohibited
until such time as the end product has been proved to conform to the provision of the Directives
2006 / 42 / EC.
Wuppertal, the 1st of January 2010
i.V.
Name: Torsten Bröker
Position: Manager, Design and Development
This Declaration does not give assurance of properties in the sense of product liability. The safety instructions
provided in the product documentation must be observed at all times.
Gravity-Feed Cup
Material connections
Gravity-Feed Cup
PLUS
Material connections
PLUS
Gravity-Feed Cup
Material connections
Adhesive Gravity-Feed Cup
Adhesive Material connections
Adhesive Gravity-Feed Cup
Adhesive Material connections
DIN EN 1953
DIN EN 13463-1
Tech.File,Ref.:
II 2 G c T 6
2413
25
V 10 701
V 10 702
V 10 703
V 10 704
V 10 705
V 10 706
V 10 715
V 10 716
V 10 711
V 10 712