Environmental Protection - Narex EBD 30-8 Instrucciones De Uso

Tool clamping
If the nut (5) is tightened, hold the spindle firmly (8) by one of the two
wrenches (9) and unscrew the nut (5) using the second wrench (9).
Push the tool (6) clamping stalk (6a) in the spring collet chuck as deep as
possible (7). The tool must not protrude from the spring collet chuck by
more than is the dimension "l".
The dimension "l" for tools with stalk diameter (6) and = 6 mm is stated in
the below table:
d (mm)
12
16
20
25
l
d
Tighten the clamping nut (5) by holding the spindle (8) firmly by one of the
two wrenches (9) and screw the nut (5) in, using the second wrench (9).
Caution! First let the new tool run without load for about 1 minute.
Use only well balanced tools of top quality with max. run-out value of
0.1 mm at the outer edge of the tool.
Maintenance

The vent holes (14) of the engine cover must not get plugged.
After about 100 hours of operation the following works need to be
done:
 - Check of the brushes length Brushes shorter than 5 mm must be
replaced with new ones.
To keep the protection class the machine needs to be checked in terms
of safety, and therefore these works must be carried out in an authorised
electric workshop holding the relevant licence to perform these kinds of
activities.
Storage
Packed appliance may be stored in dry, unheated storage place with
temperature not lower than –5°C.
Unpacked appliance should be stored only in dry storage place with
temperature not lower than +5°C with exclusion of all sudden temperature
changes.

Environmental protection

Power tools, accessories and packaging should be sorted for environmental-
friendly recycling.
Only for EU countries:
Do not dispose of power tools into household waste!
According to the European Directive 2002/96/EC on waste electrical and
electronic equipment and its incorporation into national law, power tools
that are no longer suitable for must be separately collected and sent for
recovery in an environmental-friendly manner.
Warranty
Our equipment is under warranty for at least 12 months with regard to
material or production faults in accordance with national legislation. In the
EU countries, the warranty period for exclusively private use is 24 months
(an invoice or delivery note is required as proof of purchase).
Damage resulting from, in particular, normal wear and tear, overloading,
improper handling, or caused by the user or other damage caused by not
following the operating instructions, or any fault acknowledged at the time
of purchase, is not covered by the warranty.
Complaints will only be acknowledged if the equipment has not been
dismantled before being sent back to the suppliers or to an authorised
NAREX customer support workshop. Store the operating instructions, safety
notes, spare parts list and proof of purchase in a safe place. In addition, the
manufacturer's current warranty conditions apply.
l (mm)
50
50
40
35
a
Information about noise level and
vibrations
The values have been measured in conformity with ČSN EN 60745.
Acoustic pressure level L = 82 dB (A).
pA
Acoustic power level L = 93 dB (A).
wA
In accuracy of measurements K = 3 dB (A).
Wear noise protectors!
For EBD 30-8 and EBD 30-8 E:
The weighted value of vibrations affecting hands and arms = 13 m.s
In accuracy of measurements K = 1.5 m.s
Pro EBK 30-8 E:
The weighted value of vibrations affecting hands and arms = 15 m.s
Certificate of Conformity
We declare that the device meets requirements of the following standards
and directivesc.
Safety:
EN 60745-1; EN 60745-2-3
Directive 2006/42/EC
Electromagnetic compatibility:
ČSN EN 55014-1; ČSN EN 55014-2; ČSN EN 61000-3-2; ČSN EN 61000-3-3
Directive 2004/108/EC
2010
Narex s.r.o.
Chelčického 1932
470 01 Česká Lípa
Changes are reserved
English
.
-2
.
-2
.
-2
Antonín Pomeisl
CEO of the company
01. 02. 2010
17