Specific Safety Instructions; Technical Data - REMS Nano Instrucciones De Uso

eng
only operate the power tool when they are over 16, when this is neces-
sary for their training and when they are supervised by a trained opera-
tive.
D) Power tool use and care
a) Do not force the power tool. Use the correct power tool for your
application. The correct power tool will do the job better and safer at
the rate for which it was designed.
b) Do not use the power tool if the switch does not turn it on and off.
Any power tool that cannot be controlled with the switch is dangerous
and must be repaired.
c) Disconnect the plug from the power source before making any
adjustments, changing accessories, or storing power tools. Such
preventive safety measures reduce the risk of starting the power tool
accidentally.
d) Store idle power tools out of the reach of children and do not allow
persons unfamiliar with the power tool or these instructions to
operate the power tool. Power tools are dangerous in the hands of
untrained users.
e) Maintain power tools. Check for misalignment or binding of moving
parts, breakage of parts and any other condition that may affect
the power tools operation. If damaged, have the power tool repaired
by a qualified expert or by an authorised REMS after-sales service
facility before use. Many accidents are caused by poorly maintained
power tools.
f) Keep cutting tools sharp and clean. Properly maintained cutting tools
with sharp cutting edges are less likely to bind and are easier to
control.
g) Secure the workpiece. Use clamps or a vice to hold the workpiece.
This is safer than holding it with your hand, and also it frees both hands
to operate the equipment.
h) Use the power tool, accessories and tool bits etc., in accordance
with these instructions and in the manner intended for the particular
type of power tool, taking into account the working conditions and
the work to be performed. Use of the power tool for operations different
from those intended could result in a hazardous situation. All unauthor-
ised modifications to the power tool are prohibited for safety reasons.
E) Battery tool use and care
a) Ensure the switch is in the off position before inserting battery
pack. Inserting the battery pack into power tools that have the switch
on invites accidents.
b) Recharge only with the charger specified by the manufacturer. A
charger that is suitable for one type of battery may create a risk of fire
when used with another battery pack.
c) Use battery tools only with specifically designated battery packs.
Use of any other battery packs may create a risk of injury and fire.
d) When battery pack is not in use, keep it away from other metal
objects like paper clips, coins, keys, nails, screws, or other small
metal objects that can make a connection from one terminal to
another. Shorting the battery terminals may cause bums or a fire.
e) Under abusive conditions, liquid may be ejected from the battery,
avoid contact. If contact accidentally occurs, flush with water. If
liquid contacts eyes, additionally seek medical help. Liquid ejected
from the battery may cause irritation or bums.
f) Do not use the battery/charger at battery/charger temperatures or
ambient temperatures of ≤ 5°C/40°F or ≥ 40°C/105°F.
g) Do not dispose defective batteries in the normal domestic waste.
Take them to an authorised REMS after-sales service facility or to
a reputed waste disposal company.
F) Service
a) Have your power tool serviced by a qualified repair person using
only identical replacement parts. This will ensure that the safety of
the power tool is maintained.
b) Comply with maintenance instructions and instructions on tool
replacements.
c) Check mains lead of power tool regularly and have it replaced by
a qualified expert or an authorised REMS after-sales service facility
in case of damage. Check extension cable regularly and replace it
when damaged.
Specific Safety Instructions
● Do not overload the electric pipe cutting machine. Do not use damaged
cutting wheels. Use moderate feeding pressure.
● Caution! Keep hair, clothing and gloves away from the pipe rest when
a pipe is rotating in the rollers. Loose clothing, jewellery or long hair
could get caught between the rotating pipe and the rollers.
● Do not reach into the rotating cutting wheel.
● Where necessary use a material support REMS Herkules (Art. No.
120100) on each side to support long pipes and position the pipe and
material support(s) exactly with the pipe support (6) of the electric pipe
cutting machine.

1. Technical Data

1.1. Article Numbers
REMS Nano
REMS cutting wheel Cu-INOX
REMS cutting wheel V
REMS Herkules material support on tripod
REMS Herkules Y material support clamping fixture
REMS Jumbo folding workbench
1.2. Application Area
Pipes of pressfitting systems made of
● stainless steel, C-steel (not jacketed)
● semi-hard and hard copper
● composite pipes
1.3. Speed
Idle speed of cutting wheel
1.4. Electrical Data
230 V 1~; 50 – 60 Hz; 200 W
fuse protection (mains) 10 A (B), intermittent service AB 2/10 min,
insulated, interference suppressed.
1.5. Dimensions
L × W × H:
1.6. Weights
1.7. Noise Data
Workplace-related emission value
1.8. Vibrations
Weighted effective value of the acceleration
2. Commissioning
2.1. Electrical Connection
Pay attention to main voltage! Before connecting the device, make
sure that the voltage specified on the rating plate matches the mains
supply.
2.2. Installation of the Machine
Place the electric pipe cutting machine on a workbench or similar or
unscrew the pipe arm (2) and clamp the base frame (1) in a vice or
bolt the base frame to the workbench with bolts through holes (3).
Where applicable, longer pipes must be supported on both sides with
REMS Herkules (Art. No. 120100).
2.3. Installing (changing) the cutting wheel (4)
Pull out the mains plug! Select a suitable cutting wheel:
● REMS cutting wheel Cu-INOX for stainless steel pipes, steel pipes
and copper pipes of the pressfitting systems.
● REMS cutting wheel V for multi-layered composite pipes of the
pressfitting systems.
Remove hexagonal nut (5) with size 10 ring spanner. Insert (change)
cutting wheel (4). Make sure that the carrier pins of the drive shaft grip
into the holes of the cutting wheel. Replace the hexagonal nut (5).
Caution: If an unsuitable cutting wheel is used, the wheel will be
damaged or the pipe will not be cut. Only use original REMS cutting
wheels!
eng
844000
844050
844051
120100
120130
120200
Ø 12 – 28 mm
Ø 12 – 35 mm
Ø 12 – 40 mm
125 rpm
405 × 90 × 103 mm (10" × 3.5" × 4")
1.9 kg (4 lb)
76 dB(A)
2.5 m/s²