Initial Operation; Attaching The Additional Handle - Metabo RF 14-115 Instrucciones De Manejo

Impurities that manage to enter the
machine may block the switching
mechanism. This is why, when the machine is
running, it is necessary to blow compressed air
through the rear ventilation slots of the machine
regularly, frequently and thoroughly. The machine
must be held firmly in this case.
Dust from material such as paint containing lead,
some wood species, minerals and metal may be
harmful. Contact with or inhalation of the dust may
cause allergic reactions and/or respiratory diseases
to the operator or bystanders.
Certain kinds of dust are classified as carcinogenic,
such as oak and beech dust, especially in
conjunction with additives for wood conditioning
(chromate, wood preservative). Material containing
asbestos must only be treated by specialists.
- For efficient dust collection, use a suitable
Metabo M-class vacuum cleaner together
with this power tool.
- The work place must be well ventilated.
- The use of a dust mask of filter class P2 is
recommended.
Follow national requirements for the materials you
want to work with.
Materials emitting dusts or vapours that may be
harmful to health (e.g. asbestos) must not be
processed.
When working in dusty conditions, ensure that
ventilation openings are not blocked. If it becomes
necessary to remove dust, first disconnect the
power tool from the mains supply (use non-metallic
objects) and avoid damaging internal components.
Damaged, eccentric or vibrating tools must not be
used.
Avoid damage to gas or water pipes, electrical
cables and load-bearing walls (static).
Connect a FI circuit-breaker with max.
release current (30 mA) upstream when using the
machine outdoors!
Pull the plug out of the socket before making any
adjustments, converting or servicing the machine.
A damaged or cracked additional handle must be
replaced. Never operate a machine with a defective
additional handle.
A damaged or cracked safety guard must be
replaced. Never operate a machine with a defective
safety guard.
SYMBOLS ON THE TOOL:
........... Class II Construction
V............... volts
A .............. amperes
Hz ............ hertz
W ............. watts
~
.............. alternating current
rpm ......... revolutions per minute
.../min...... revolutions per minute
n.............. rated speed
4. Overview
See page 2.
1 Extractor connection piece
2 Threaded holes on gear housing (both sides)
3 Thumb screws
4 Additional handle
5 Locking discs
6 2-hole spanner
7 Routing tool*
8 Spindle
9 Spindle locking button
10 Clamping nut *
11 Diamond cup wheel*
12 Support flange *
13 Screw *
14 Safety disc*
15 Sliding on/off switch
16 Handle
17 Electronic signal indicator
18 Speed adjustment wheel
19 Safety guard
20 Flat area for working close to edges
21 Wing nut
22 Depth stop
* depending on equipment/not in scope of delivery

5. Initial Operation

Before plugging in the device, check that the
rated mains voltage and mains frequency, as
specified on the rating label, match your power
supply.
5.1

Attaching the additional handle

Always work with the additional handle
attached (4)! Attach the auxiliary handle as
shown.
See illustration A on page 2.
- Fit locking discs (5) to the left and right of the gear
housing.
- Fit the additional handle (4) on the gear housing.
- Insert the thumb screws (3) to the left and right of
the additional handle (4) and turn gently.
- Adjust the additional handle to the required angle
(4).
- Manually tighten the thumb screws (3) to the left
and right.
5.2 Adjusting the depth stop
For safety reasons, only use the safety guard
(19) provided.
See figure, page 2.
- Release wing screw (21).
- Twist the depth stop (22) to adjust the height in
relation to the accessory and the work task.
- Hand-tighten the wing screw (21) securely.
ENGLISH en
7