General Maintenance - EGO LB6000E Manual De Usario

To Adjust The Support Harness
1. Put your arms through the backpack straps to support
the blower on your back.
2. Temporarily adjust both shoulder straps to comfort-
able positions (Fig. J), making sure that your elbow is
comfortable.
3. Snap the chest buckle and adjust its length if neces-
sary (Fig. K).
4. Snap the waist buckle and adjust its length so that the
backpack is securely supported by your hips
(Fig. L & M).
NOTICE:
The backpack shouldn't sit too high on your
back; it should be positioned closer to your hips than to
your shoulders.
5. Readjust the shoulder straps for security and comfort.
Makes sure that the backpack sits securely on your
back, with the weight supported by the waist strap,
and without excess movement when you move (Fig. O).
6. Insert any extra length of belt around the waist into the
elastic on both sides (Fig. P).
7. To detach the tool from your back, just press the waist
and chest buckles to release them and lower the tool
(Fig. Q).
To Adjust The Control Handle
1. Loosen the wing nut to adjust the handle forward or
backward as needed (Fig. R & S) and then tighten the
wing nut to secure the position of the handle.
2. You may also rotate the handle as needed for comfort
(Fig. T).
3. To enlarge the area you are cleaning, move the tube to
the left or the right (Fig. U).
STARTING/STOPPING THE BLOWER (Fig. V)
1. To start the blower, press down on the lock-off lever
and hold it, then depress the trigger. The blower will
begin to run.
2. To stop the blower, release the trigger.
ADJUSTING THE AIR SPEED (Fig. V)
The blower is equipped with stepless speed regulation to
control air speed.
1. To increase the air speed, pull the variable-speed lever
downward when the blower runs; to reduce the air
speed, push the knob upward.
2. To boost the air speed at any setting, press the boost
button to increase the air speed to the maximum. The
blower will resume the previously selected speed when
this button is released.
56 VOLT LITHIUM-ION CORDLESS BACKPACK BLOWER — LB6000E
Fig. V parts description see below:
V-1 Boost Button
V-2 Variable-Speed Lever V-4
TIPS FOR USING THE BLOWER
◾
To keep from scattering debris, blow around the outer
edges of a debris pile. Never blow directly into the
center of a pile.
◾
To reduce sound levels, limit the number of pieces of
equipment used at any one time.
◾
Use rakes and brooms to loosen debris before blowing.
In dusty conditions, slightly dampen surfaces if water
is available.
◾
Watch out for children, pets, open windows, or freshly
washed cars, and blow debris safely away.
◾
After using blowers or other equipment, clean up!
Dispose of debris properly.
MAINTENANCE
WARNING:
When servicing, use only identical
replacement parts. Use of any other parts may create a
hazard or cause product damage. To ensure safety and
reliability, all repairs should be performed by a qualified
service technician.
WARNING:
To avoid serious personal injury, always
remove the battery pack from the product when cleaning
or performing any maintenance.

GENERAL MAINTENANCE

Avoid using solvents when cleaning plastic parts. Most
plastics are susceptible to damage from various types of
commercial solvents and may be damaged by their use.
Use clean cloths to remove dirt, dust, oil, grease, etc.
WARNING:
Do not at any time let brake fluids,
petrol, petroleum-based products, penetrating oils,
etc., come in contact with plastic parts. Chemicals can
damage, weaken or destroy plastic which may result in
serious personal injury.
STORAGE
◾
Remove the battery pack from the blower.
◾
Clean all foreign material from the air inlets of the
blower.
◾
Align the blower-tube storage knob with the tube-
hanging groove and hook the blower tube onto the
battery compartment housing (Fig. W & X).
◾
Store in an enclosed space that is inaccessible to
children. Keep away from corrosive agents, such as
garden chemicals and de-icing salts.
EN
V-3 Trigger
Lock-off Lever
13