Dyson V8 Manual De Instrucciones página 38

EN
USING YOUR DYSON MACHINE
PLEASE READ THE 'IMPORTANT SAFETY INSTRUCTIONS' IN YOUR DYSON USER
MANUAL BEFORE PROCEEDING.
INSTALLING YOUR DOCKING STATION
• Use appropriate mounting hardware for your wall type and ensure that the docking
station is mounted securely. Ensure no pipe work (gas, water, air) or electrical
cables, wires or ductwork are located directly behind the mounting area. The
docking station must be mounted in accordance with regulations and applicable
codes/standards (state and local laws may apply). Dyson recommends the use of
protective clothing, eyeware and materials when installing the docking station.
OPERATION
• Do not use outdoors or on wet surfaces or to vacuum water or other liquids –
electric shock could occur.
• Ensure the appliance remains upright in use and in storage. Dirt and debris may be
released if it is turned upside down.
• Do not operate while checking for blockages.
• For domestic indoor and car use only. Do not use it whilst the car is in motion or
while driving.
• To operate the Max mode, locate the switch on the top of the appliance. Slide the
switch to the Max mode position.
• To switch off Max mode, slide the switch back to the Powerful suction
mode position.
• Your machine has carbon fibre brushes. Take care if coming into contact with
them, as they may cause minor skin irritation. Wash your hands after handling
the brushes.
USING YOUR MACHINE
• Do not use without the clear bin and filter(s) in place.
• Fine dirt such as flour should only be vacuumed in very small amounts.
• Do not use the appliance to pick up sharp hard objects, small toys, pins, paper
clips, etc. They may damage the appliance.
• When vacuuming, certain carpets may generate small static charges in the clear
bin or wand. These are harmless and are not associated with the mains electricity
supply. To minimise any effect from this, do not put your hand or insert any object
into the clear bin unless you have first emptied it. Clean the clear bin with a damp
cloth only. (See 'Cleaning the clear bin'.)
• Use extra care when cleaning on stairs.
• Do not rest the appliance on chairs, tables, etc.
• Do not press down on the nozzle with excessive force when using the appliance as
this may cause damage.
• Do not leave the cleaner head in one place on delicate floors.
• On waxed floors, the movement of the cleaner head may create an uneven lustre.
If this happens, wipe with a damp cloth, polish the area with wax, and wait for it
to dry.
CARPETS OR HARD FLOORS
• Before vacuuming your flooring, rugs and carpets, check the manufacturer's
recommended cleaning instructions.
• The brush bar on the machine can damage certain carpet types and floors. Some
carpets will fuzz if a rotating brush bar is used when vacuuming. If this happens, we
recommend vacuuming without the motorised floor tool and consulting with your
flooring manufacturer.
• Before vacuuming highly polished floors, such as wood or lino, first check that the
underside of the floor tool and its brushes are free from foreign objects that could
cause marking.
DIAGNOSTICS – LIGHTS DURING CHARGING
Charging, low charge.
Charging, medium charge.
Charging, nearly full.
Fully charged.
Battery fault – call the
Dyson Helpline.
Charger fault – call the
Dyson Helpline.
DIAGNOSTICS – DURING USE
38
EMPTYING YOUR CLEAR BIN
High level of charge.
Medium level of charge.
Low level of charge.
Empty, needs recharging.
Battery fault – call the
Dyson Helpline.
Main body fault – call the
Dyson Helpine.
• Empty as soon as the dirt reaches the MAX level – don't overfill. Using the machine
when the dirt is above the MAX line may cause the dirt to reach the filter and more
frequent maintenance will be required.
• Ensure that the appliance is disconnected from the charger before emptying the
clear bin. Be careful not to pull the 'ON' trigger.
• To make emptying the clear bin easier, it is advisable to remove the wand and
floor tool.
• To minimise dust/allergen contact when emptying, cover the clear bin tightly in a
dust proof bag while you empty.
• To release the dirt, hold the appliance by the handle, pull the red lever back and lift
upwards to release the cyclone. Continue until the bin base automatically opens
and releases the dirt.
• Remove the clear bin carefully from the bag.
• Seal the bag tightly and dispose.
• To close, push the cyclone downwards until it is in the normal position and manually
close the base of the bin – the base will click when it is securely in place.
CLEANING THE CLEAR BIN
• Ensure the appliance is disconnected from the charger before removing the clear
bin. Be careful not to pull the 'ON' trigger.
• Remove the wand and floor tool.
• To remove the cyclone, hold the appliance by the handle, pull the red lever towards
you and lift upwards until the bin opens, then push in the red button located behind
the cyclone and lift the cyclone out.
• To detach the clear bin from the appliance, pull back on the red catch located at the
base, slide the clear bin down and carefully remove forwards from the main body.
• Clean the clear bin with a damp cloth only.
• Do not use detergents, polishes or air fresheners to clean the clear bin.
• Do not put the clear bin in a dishwasher.
• Ensure the clear bin is completely dry before replacing.
• To replace the clear bin, align the tabs on the clear bin with the grooves on the main
body and slide upwards into place until the catch clicks.
• Slide the cyclone into the grooves of the main body and push downwards until it is in
its normal position and manually close the base of the bin – the base will click when
it is securely in place.
WASHABLE PARTS
Your machine has washable parts, which require regular cleaning. Follow the
instructions below.
WASHING THE BRUSH BAR
• Your appliance has a washable brush bar, check and wash it regularly according to
the following instructions to maintain performance.
• Ensure the appliance is disconnected from the charger before removing the brush
bar. Be careful not to pull the 'ON' trigger.
TO REMOVE, WASH AND REPLACE THE BRUSH BAR:
• Please refer to the 'Washing the brush bar' illustrations alongside the
instructions below.
• Turn the cleaner head upside down so the underside of the cleaner head is
facing you. Use a coin to turn the fastener one quarter anti-clockwise to the
unlocked position.
• Rotate the end cap to the open position. Gently slide the brush bar away from the
cleaner head.
• Remove the end cap from the brush bar.
• Hold the brush bar under running water and gently rub to remove any lint or dirt.
• Stand the brush bar upright as shown. Leave to dry completely for a minimum of
24 hours.
• Before replacing, check that the brush bar is completely dry.
• Reattach the end cap to the brush bar.
• Slide the brush bar back onto the cleaner head, around the motor. The end cap
should be in the open position as shown. Once in place, rotate the end cap back
into the closed position.
• Close the fastener by turning a quarter turn clockwise. Ensure that the fastener is
fully turned and the brush bar is secure.