Child Safety - Hoover FE GD21 RB Instrucciones De Uso

PYROLYSE
The oven is equipped with a pyrolyser cleaning system, which
destroys food residues at high temperature. The operation is carried
out automatically by means of the programmer. The resulting fumes
are rendered "clean" by passing over a Pyrolyser wich starts as
soon as cooking begins. As very high temperatures are required
by the Pyrolyser, the oven door is fitted with a safety lock.
The pyrolyser can be stopped at any time. The door cannot be
opened until the safety lock is displayed.
NOTA : if a hob has been fitted above the oven, never use the gas
burners or the electric hot-plates while the Pyrolyser is working,
this will prevent the hob from overheating.
THREE PYROLYTIC CYCLE are pre-set.
. ECO PYROCLEAN : cleans a moderately stained oven. Operates
at a temperature of 475°C for a period of 90 minutes.
. NORMAL PYROCLEAN : cleans a normaly stained oven. Operates
at a temperature of 475°C for a period of 105 minutes.
. SUPER PYROCLEAN : cleans an heavily stained oven. Operates
at a temperature of 475°C for a period of 120 minutes.
Never use commercially available cleaning products on a Pyrolytic
oven !
Tip : carrying out Pyrolytic cleaning immediately after cooking allows
you to take advantage of residual heat, thus saving energy.
Before carrying out a Pyrolytic cycle :
- Remove all accessories from the oven : they cannot withstand
the high temperatures and would be damaged by pyrolytic
temperatures.
- Remove any large spillages or stains as it would take too long
to destroy them. Also excessively large amounts of grease could
ignite when subject to the very high temperatures of the Pyrolytic-
cycle.
- Close the oven door.
Using the pyrolytic cycle :
1- Turn the function selector knob to "Pyrolytic Mode".
2- By using the central button select the required Pyrolytic mode,
according the degree of staining :
.. ECO PYROCLEAN .. NORM PYROCLEAN .. SUPER PYROCLEAN ..
Confirm the choice by pressing the central button.
... the oven starts the pyrolytic cycle.
On the display, the time of the end pyrolytic cycle and the "time"
and "stop" indicator lights will appear.
During the pyrolytic cycle, the locking oven door appears, it indicates
that the door is locked. The cooling fan will operate.
The indicator light flashes until the temperature required is not
reached and then it becomes fixed.
* The start of the pyrolytic cycle can be delayed by selecting an
end of time. Turn the programmation control knob to the end of
time and set the end of time required.
At the end of the pyrolytic cycle the oven will automatically switch
off.
For 15 seconds,an audible signal lets you know that the cycle has
ended and the "time" and "Stop" indicator lights will flash.
. Turn the selector knob to STOP. Unless you do this, the symbols
will continue flashing.
The oven door will remain locked until the temperature is high. So,
as the locking oven door is light, the oven can not be opened.
The cooling fan does not switch itself off until the temperature of
the oven components is reasonable.
At the end of the cycle, the indicator flashes again and stays lighted
even if the oven is switched off. It disappears only when the
temperature is sufficiently low.
Pyrolysis leaves a white residue on the oven walls. Wait for the
oven to cool completely then clean the inside of the oven with a
damp sponge to wipe off the residue.
The electronic control system records all of the cooking settings
used and with frequent usage it will calculate the degree of dirt
build up and indicate the need for cleaning.
To begin the pyro cycle follow the above instructions.
At the end of the cleaning cycle the memory will automatically reset
itself.

CHILD SAFETY

This function is essential, especially when children are around. It
prevents children from switching the oven on or altering the pre-
set programmes.
This safety system locks the oven control panel while it is operating.
There are two levels of safety :
LIVEL 1 : Locking selector control knob and the central button.
. To activate : turn the programmation control knob to child safety.
. Action : the control knobs are inactive*.
. To deactivate : turn the programmation control knob to 0.
LIVEL 2 : Locking function selector knobs
. To activate : turn the function selector knob to child safety and
keep the central button pressed in for 3 seconds.
. Action : all the controls are inactive*.
. To dactivate : the same procedure as for activating. Turn the
function selector knob to child safety and keep the central button
pressed in for 3 seconds.
*Nota : in all cases, for reasons of safety, even when the controls
are locked, the oven can be switched off by turning the selector
knob to 0.
24 GB