Mr. Heater MH8BXDF Manual De Instrucciones página 5

Figure 4: „Butane Adapter‰
thread sealant on this connection. Screw butane propane
mixture cartridge into the adapter (clockwise), once
the shaft on the adapter starts to turn the cartridge is
connected, then fit the cartridge into the stand.
•
Check adapter and cartridge connection for leaks with
soapy water at the threaded connection under the
domed plastic cover where the cartridge screws into the
regulator. SEE WARNING! ON DOMED PLASTIC COVER.
•
Turn Control Knob counterclockwise to „PILOT‰ position
and depress to
light; see Figure 1 and
Figure 3.
•
If heater does not light,
hold down for ap-
proximately 30 seconds;
release and depress
again. Repeat until pilot
lights.
•
After pilot lights,
hold down for 30 -60
seconds and then
release knob. Knob
should return to fully
extended position; To operate heater slightly depress knob
and gently turn to lock in the „HI‰ position
burner tile. Leave on „HI‰
turns bright orange. Figure 5
NOTE: Flare ups are common when first lighting the
appliance. Keep your face and flammable objects away
from the appliance.
•
After burner tile has turned bright orange, adjust heat out-
put by turning Control Knob to desired position („LO‰
or „HI‰ setting) Figure 1.
Warning:
DO NOT OPERATE HEATER UNLESS CONTROL KNOB IS
LOCKED IN A POSITION MARKED „HI‰
„PILOT‰ .NEVER SET CONTROL KNOB BETWEEN
LOCKED POSITIONS. POOR COMBUSTION AND HIGHER
LEVELS OF CARBON MONOXIDE MAY RESULT.
•
To shut off heater, slightly push down and turn Control
Mr. Heater | Portable Propane and Butane/Propane Mixture Heater
SEALS
Adapter Shaft
Figure 5: „Release knob.
to light
position until burner tile
, „LO‰
Knob clockwise to „OFF‰ position
•
CAUTION: Accessible parts may become very hot. The
guard on this appliance is to prevent risk of fire or injury
from burns and no part of it should be permanently
removed. IT DOES NOT GIVE FULL PROTECTION FOR
YOUNG CHILDREN OR THE INFIRM. Allow to thoroughly
cool before storing.
• Turn knob to „OFF‰ position
are extinguished before disconnecting the gas cartridge.
• TO REMOVE PROPANE (G31) CARTRIDGE: Remove
cartridge from stand and turn cartridge counterclockwise
until it is fully unscrewed off of heater.
• TO REMOVE BUTANE/PROPANE MIXTURE (G30+G31)
CARTRIDGE: Remove cartridge from stand and turn
cartridge counterclockwise until it is fully unscrewed off
of adapter.
• Once Cartridge is removed then the Butane adapter can
be unscrewed turning counterclockwise until it is fully
unscrewed off of the heater.
•
Do not operate, store or remove cartridge near
flammable items or ignition sources. Only change
cartridges in a well ventilated location, preferably
outside, away from any sources of ignition such as naked
flames, pilots, electric fires and away from other people.
• Propane-GAS (G31) or Butane/Propane mixture
(G30+G31) cartridges MUST BE DISCONNECTED FROM
HEATER WHEN NOT IN USE! Make sure to check the
seals before connecting a new gas cartridge to the ap-
pliance.
MAINTENANCE:
PRECAUTIONS TO
BE TAKEN WHEN
THE APPLIANCE IS
NOT TO BE USED
FOR A PERIOD OF
TIME:
Always keep the
heater area clear
and free from
combustible
materials, gasoline
and other flammable vapors and liquids.
Store heater when it has cooled in a zippered bag or other
sealed dust free location between uses.
Keep the vent areas (slots in the bottom and the top at the
front of heater) clear at all times.
Visually inspect the pilot flame and burner periodically dur-
ing use. The pilot flame should be blue in color (not yellow)
and will extend beyond the thermocouple. The flame will
surround the thermocouple just below the tip, see Figure 6.
A slight yellow flame may occur where the pilot flame
or
and main burner flame meet. The burner should be bright
orange (with a slight blue color around the border, a red-
orange haze that is visible on the ceramic tile is acceptable)
and without a noticeable flame. A blue flame that rolls out
at the top of the ceramic tile indicates an accumulation of
5
Operating Instructions and OwnerÊs Manual
.
. Check that burners
Figure 6