Jacuzzi Flexa Therma ST2 Manual De Instalación Y Servicio página 13

i
I
( 13, detail 1 ) Place the right fixed glass panel (A1) on the
shower tray checking that:
1a) The runner groove of the lower slide fits into the relevant edge
of the shower tray;
1b) The fixed glass panel upright is placed inside the wall panel
profile;
i
I
( 13, detail 2) Then fasten the glass panel unit to the wall pan-
el profile with the 5 screws + 5 washers provided.
i
I
( 14, detail 1) Place the left fixed glass panel (A) on the show-
er tray checking that:
1a) The bottom sliding profile fits into the bottom angle bar (C);
1b) The bottom slide's groove fits into the shower tray's raised edge;
1c) The fixed glass panel upright is placed inside the wall panel
profile;
1d) The top sliding profile fits into the top angle bar (C1);
i
I
( 14, detail 2) Then fasten the bottom left sliding profile to
the angle bar (C).
i
I
( 14, detail 3) Fasten the top left sliding profile to the angle
bar (C1).
i
I
( 14, detail 4) Then fasten the glass panel unit to the wall pan-
el profiles with the 5 screws +5 washers provided.
For the ROUND model only
i
I
( 13a, detail 1) Place the fixed glass panel (A) on the show-
er tray checking that:
1a) The runner groove of the bottom slide fits into the edge of the
shower tray;
1b) The fixed glass panel upright is placed inside the wall panel
profile;
i
I
( 14a, detail 1) Then fasten the fixed glass panel (A) to the
wall panel profile with 10 screws + 10 washers.
For the ROUND and SQUARE models
i
I
( 1-1a) Fasten the two seals (N) (ROUND model) or the two
top seals (N) and the two bottom seals (N1) (SQUARE model) to the
sliding glass panel/s.
i
I
( 15, detail 1) Fasten the sliding glass panels by hooking the
top washers to the relevant sliding profiles.
i
I
( 15, detail 2) Using the screws on the supports, lift up the
glass panels so that the sliding blocks fit into the bottom slide. Dur-
ing this operation also check that the glass panels are perfectly ver-
tical and slide easily.
i
I
( 16) Fasten the glass panel unit to the shower tray with 4 met-
al brackets (in the hardware pack) by inserting them first into the run-
ner groove of the bottom slide and then fix them to the shower tray us-
ing 4 screws and washers.
Top installation (if provided)
i
I
( )
17, detail 1 Place the top over the shower enclosure, so that
the edge fits into the runner groove of the top slide; instead the back
edge of the top must rest on the metal frame of the wall panel, to which
the top must be fastened using 4 screws and 4 washers.
i
I
( )
17, detail 2 Then connect the shower head's fabric-finish
rubber hose to the respective solenoid valve on the left side of the
shower enclosure using a metal clamp; be careful not to tighten it
too hard or you may cut the hose.
ONLY FOR ELT 22
i
I
( 17, detail 3 ) Connect the "Cromodream" cable to the ca-
ble coming from the electric wiring box, using a quick release con-
nector (also check the related electrical component diagram).
Plumbing and electrical connections
i
I
( 18, detail 1 ) Move the shower enclosure close enough to
the wall to enable the connection of the flexible hoses to the out-
lets provided in the wall.
FOR ELT 3, 4, 22
I
Follow the instructions in the "Electrical Safety" chapter
very carefully.
-Follow the L phase, N neutral and
-Remove the lid of the indicated electric wiring box and, after hav-
ing connected, close the lid carefully and tighten the cable clamps
well, in order to guarantee protection from water jets.
IMPORTANT: for Countries where 220-240V voltage
is supplied by a two-phase system (L+L), the connec-
tion has to be made on terminals L and N anyway.
Connect the main supply cable, coming from the electric network
of the building, to the electric wiring junction box; refer to the elec-
tric wiring diagram of the model provided.
Connection of alarm (if provided)
The ELT3, 4, 22 models have been designed with an "alarm" provi-
sion (button ). If the building has a "call for help" circuit, it can be
connected to the shower enclosure and controlled by that button.
Inside the electronic control box, near the "ALARM" watertight cable
clamp (see wiring diagram), there are two terminals marked with "ALL".
These terminals correspond to the normally open contacts of a relay
to which the installer can connect the emergency call circuit, which must
comply with current legislation and specific national standards.
When the alarm button is pressed on the display panel, a relay, al-
ready mounted inside the electronic box, activates the emergency
call device for about 15 seconds. The call indicator (bells, buzzers,
lamps, etc.) can be powered either with 220/240V or low voltage,
but with a maximum current absorption of 10 A.
The alarm connection must be made using a cable with specifica-
tions of not less than type H 05 VV-F 2x2.5 mm
The use of this cable is essential to ensure that the cable clamp fit-
ted on the box has the level of protection (waterproofing) required
by regulations.
13
earth symbols.
2 .