Kenmore 110.2810 Serie Manual De Uso Y Cuidado página 18

First try the solutions suggested here or visit for assistance and to possibly avoid a service call�
If you experience
Washer not performing as expected (cont.)
Incorrect dispenser
operation
Single-dose laundry
packet not dissolving
Error Code Appears in Display
oL (overloaded) appears
in display
uL (unbalanced load)
appears in display
LF (too long to fill)
appears in display
Ld (too long to drain
water) appears in display
HC (hot and cold hoses
reversed) appears in
display
Sd (Excess suds)
appears in display
dL (Lid cannot lock)
appears in display
lid (Lid opened) appears
in display
dU (Lid cannot unlock)
appears in display
F## code (F-type error
code) appears in display
18
TROUBLESHOOTING
Possible Causes
Clogged dispensers or laundry
products dispensing too soon�
Liquid chlorine bleach not used in
dispenser or Timed Oxi option not
selected�
Adding laundry packet incorrectly�
Load too large�
Load not balanced. The washer is
running a load-balance correction
routine�
Washer taking too long to fill. Drain
extends more than 4.5" (114 mm) into
standpipe�
Washer taking too long to drain
water. Drain extends more than
4.5" (114 mm) into standpipe.
Hot and cold inlet hoses have been
installed incorrectly�
Excessive suds in washer. Washer is
running a suds reduction routine�
An item in the load may be keeping
the lid from locking�
Washer lid left open�
Objects on washer lid prevent it from
unlocking�
System error code�
Do not overfill dispenser. Overfilling causes immediate dispensing.
Always select Fabric Softener option to assure proper dispensing.
Load dispensers before starting a cycle�
It is normal for small amounts of water to be remain in dispenser
at the end of the cycle�
Homes with low water pressure may result in residual powder
in the dispenser. To avoid, select a warmer wash temperature if
possible, depending on your load.
Use only liquid chlorine bleach in the bleach dispenser�
You may only place Oxi products directly in the liquid chlorine
bleach dispenser. If using Oxi products, be sure to select Timed
Oxi option� Do not use both liquid chlorine bleach and Oxi
product in the same load�
Be sure laundry packet is added to washer basket before adding
clothes. Follow the manufacturer's instructions to avoid damage to
your garments�
If an overload is detected, the washer will drain any water and
detergent in the washer. Remove several items and add HE deter-
gent. Close lid and press START/PAUSE/Unlock Lid.
Allow the washer to continue. If the dial is flashing and the washer
has stopped, redistribute the load, close the lid, and press START/
PAUSE/Unlock Lid.
Check plumbing for correct drain hose installation� Use drain hose
form and attach securely to drainpipe or tub� Do not tape over
drain opening� See Installation Instructions�
Check plumbing for correct drain hose installation� Use drain hose
form and attach securely to drainpipe or tub� Do not tape over
drain opening�
Lower drain hose if the end is higher than 96" (2.4 m) above the
floor. Remove any clogs from drain hose. See Installation Instruc-
tions�
This code will appear at the end of the wash cycle to indicate
that cold water hose is connected to the hot water inlet and hot
water hose is connected to the cold water inlet.
Allow the washer to continue. Use only HE detergent. Always
measure detergent, and base detergent quantity on load size.
Follow detergent manufacturer's instructions. If the dial is flashing,
reselect your desired cycle using a cold wash temperature, and
press START/PAUSE/Unlock Lid. Do not add detergent.
Check for items directly under the lid�
Close the lid to clear the display� If the lid is left open for more
than 10 minutes, the cycle will reset and water in the washer will
drain�
Remove objects, such as a basket of laundry, from the top of the
washer.
Press START/PAUSE/Unlock Lid once to clear the code. Then press
START/PAUSE/Unlock Lid again to restart washer. If code ap-
pears again, call for service.
Solution