Operating Specifications; Installation Instructions - Omnifilter A Serie Instrucciones De Instalación

OPERATING SPECIFICATIONS

Pressure Range:
Temperature Range:
Rated Flow*: 10 gpm @ 1 psi drop (38 Lpm @ 0.07 bar)
* Rated flow without cartridge. Performance will vary with type of cartridge used.
PRECAUTIONS
Carefully read and follow instructions.
WARNING
Do not use with water that is microbiologically
unsafe or of unknown quality without adequate disinfection
before or after the system.
CAUTION
Filter must be protected against freezing, which can
cause cracking of the filter and water leakage.
CAUTION
The rubber o-ring provides the water-tight seal
between the cap and the bottom of the housing. It is important
that the o-ring be properly seated in the groove above the
threads of the housing or a water leak could occur.
CAUTION
Because of the product's limited service life and to
prevent costly repairs or possible water damage, we strongly
recommend that the bottom of all plastic housings be replaced
every five years for clear and every ten years for opaque. If the
bottom of your housing has been in use for longer than this
period, it should be replaced immediately. Date the bottom
of any new or replacement housing to indicate the next
recommended replacement date.
CAUTION
Do not use electrical heating tape on this unit.
NOTES:
This filter housing does not include a filter cartridge.
•
For cold water use only.
•
The contaminants or other substances removed or reduced by
•
this water treatment device are not necessarily in your water.
Ask your local water municipality for a copy of their water
analysis, or have your water tested by a reputable water
testing lab.
Do not install where system will be exposed to direct sunlight.
•
Filter cartridge life varies depending on filter type, usage, and
•
water conditions.
The replacement filter cartridge used with this system has a
•
limited service life. Changes in taste, odor, or flow of the water
being filtered indicate that the cartridge should be replaced.
Use only OMNIFILTER replacement cartridges.
•
This installation must comply with all applicable state and
•
local regulations.
Use only Teflon tape without adhesive backing to seal joints.
®
•
Do not use pipe compound ("pipe dope"), sticks, or similar
compounds with this unit; they contain petroleum derivatives
which will cause crazing and cracking of the plastic in the
filter housing.
Use only soap and water to clean filter housing
•
and components.
Do not use aerosol sprays (bug spray, cleaning fluids, etc.)
•
near the filter. They contain organic solvents which will cause
crazing and cracking of the plastic in the filter housing.
Teflon is a registered trademark of IE DuPont de Nemours and Company, Corporation,Wilmington, Delaware
®
• 2 •
•
25–125 psi (1.7–8.62 bar)
40°F–100°F (4.4°C–38°C)
•
•
•

INSTALLATION INSTRUCTIONS

NOTE:
•
•
•
•
•
•
Installation
1.
2.
After prolonged periods of non-use, such as a vacation, it
is recommended that the system be flushed thoroughly. Let
water run for 5-6 minutes before using.
Do not use a torch or open flame near the unit.
Some harmless bacteria may attack cellulose media cartridges
(such as the TO1 or RS1). If your cartridge seems to
disintegrate or develops a musty or moldy odor, switch to a
synthetic media cartridge or consult the manufacturer.
Wear safety glasses during installation.
Please read all instructions, specifications, and precautions
before installing and using this filter.
For installation on standard 1/2-inch or 3/4-inch main water
line (galvanized, copper or plastic pipe).
Use only Teflon ® tape for fitting housing connections.
Install filter cartridge in filter housing according to the filter
cartridge replacement instructions (page 4) before proceeding
with installation. See Filter Cartridge Selection Guide on page 5
to determine the best cartridge for your filtration needs.
Install filter after water meter or pressure tank.
Numbered diagrams correspond with numbered steps.
(A) Turn off cold water supply and (B) open nearest faucet to
release pressure in pipes before starting installation. (C) Apply
about 6-inches of Teflon tape in clockwise direction to pipe
®
threads of each adapter. Install cartridge in OB1 or OB5 per
filter cartridge replacement instructions on page 4.
1
A
(D) Align filter assembly with ends of pipe, making certain
the water flow is in the direction marked on the cap. (E) Use
integral bracket cap as a template to mark screw locations
on wall. Insert mounting screws into wall. Leave a space
between the head of the screw and the wall to slip bracket
onto screws.
NOTE: Allow 1 ⁄ -inches (33 mm) clearance below housing to
1
2
enable filter cartridge changes.
2
E
D
B
C