Attachment And Operation; Initial Operation - Scheppach CSE2400 Manual De Instrucciones

• The specified vibration emission value can also be
used for an initial assessment of the load.
Warning:
• The vibration emission value can vary from the
specified value during the actual use of the electric
tool, depending on the type and the manner in
which the electric tool is used;
• Try to minimise stress from vibrations as low as
possible. Some examples of means for reducing
the vibration stress are wearing gloves while using
the tool and limiting work time. In the process all
parts of the operating cycle must be taken into
account (such as times in which the electric tool is
switched off or time in which it is switched on, but is
not running under a load).

7. Attachment and operation

Warning!
Always wear safety
protective gloves and heavy-duty work clothes!
Use the saw only with approved extension cables with
the prescribed insulation and connections designed
for outdoor use (approved rubber-sheathed cables)
which fit the chainsaw plug.
The chain saw is equipped with safety switches,
requiring the use of both hand. The chainsaw works
only when one hand is pushing the button 11 and 13
at the same time. If the chainsaw does not run, the
chain brake must be released at the front finger guard
(3). Be
sure to read the sections "Chain brake" and "
Releasing the chain brake " on this point.
To switch on:
• Release the chain brake (3), push in the lock (11)
and press the power switch (13).
• Place the lowest claw (Fig 2, J) on the wood . Raise
the chain saw by the rear grip (1 ) and saw into the
wood. Move the chain saw back a little and place
the claw further down.
• Be careful when sawing splintered wood as pieces
of wood may be ripped off.
After switching on, the chainsaw will run immediately
at high speed .
To switch off
• Release either the ON/OFF switch (13) on the rear
grip.
• The release of ON/OFF switch results the stop of
the chainsaw within 1sec., and heavy sparkling.
This is normal and safe for the proper operation of
the chainsaw.
• After working with the chainsaw, you should always:
Clean the saw chain and guide bar and replace the
chain guard.
• If the chain brake is activated the chainsam will be
deactivated immediately.
GB
28
goggles, ear muffs,

8. Initial operation

The voltage and current supply must comply with the
ratings on the type plate.
Before commencing work, always check that the
chainsaw works properly and is safe to operate.
Check also that the chain lubrication and the oil
gauge are in good working order (see Fig.4). When
the oil lever is approx. 5 mm from the bottom mark,
you must top up with oil. When the oil level is higher
you can work without worry.
• Switch on the chain saw and hold it above the
ground. Be careful not allow the chainsaw to touch
the ground. For safety reasons it is best to keep
a clearance of at least 20 cm. If you now see
growing traces of oil, the chain lubrication system
is working correctly. If there are no traces of oil at
all, try cleaning the oil outlet (Fig 2, C), the upper
chain tensioning borehole (Fig 3, e) and the oil
duct, or contact your Customer Service. (Be sure
to read the section "Filling in chain oil and chain
lubrication" on this point).
• Check the chain tension and retention, if necessary (see
the section "Tensioning the saw chain" on this point).
• Make sure the chain brake is working properly (see
also the section "Releasing the chain brake").
Assembly
Fitting the guide bar and chain (Fig 1, 2, 3)
Warning! If the chain saw is already connected to the power
supply: Pull the plug from the socket outlet. Wear protective
gloves whenever doing any work on the saw chain.
Important: The front finger guard (3) must always be
in the top (vertical) position (Fig. 5).
The guide bar and saw chain are supplied separately.
To assemble, first unscrew the lock nut (SDS-
system/5) and remove the guide bar cover (6). The
guide bolt (17) must be in the centre of the guide.
If necessary, adjust the chain tensioning with the
chain wheel (Fig.3, 5a).
Warning! To prevent injury on the sharp cutting
edges, always wear gloves when assembling,
tensioning and checking the chain.
Before assembling the guide bar with the saw chain,
check the cutting direction of the teeth!
The running direction is marked with an arrow on the
cover (6). To determine the direction of cut, it may be
necessary to turn over the saw chain (4).
Hold the guide bar (7) vertically with the tip pointing
upwards and put on the saw chain (4, beginning at
the tip of the bar.