Epson DP-502 Guia De Instalacion

DP-502 Installation Guide
EN
Guide d'installation DP-502
FR
Guía de instalación de la DP-502
ES
Guia de instalação DP-502
PT
EN Unpacking
EN Remove the connector cover. Reattach it after the DM-D110 is installed.
FR Retirez le cache-connecteurs. Fixez-le à nouveau après avoir installé l'afficheur DM-D110.
ES Extraiga la tapa de conectores. Móntela de nuevo cuando haya instalado la DM-D110.
PT Remova a tampa do conector. Recoloque-a após a DM-D110 ser instalada.
EN Use the 2 screws removed in Step 2 and the 2 included long screws.
Be sure not to connect the cables before attaching the plate. Otherwise, the cables can
be damaged.
FR Utilisez les 2 vis enlevées au point 2 et les 2 vis longues fournies avec l'appareil.
Les câbles ne doivent pas être connectés avant de fixer la plaque. Autrement, ils
risquent d'être endommagés.
ES Utilice los 2 tornillos extraídos en el paso 2 y los 2 tornillos largos suministrados.
Asegúrese de que los cables no se conecten antes de montar la placa, ya que podrían
resultar dañados.
PT Utilize os 2 parafusos removidos no Passo 2 e os 2 parafusos compridos incluídos.
Certifique-se de que não liga os cabos antes de colocar a placa. Caso contrário, os
cabos podem ser danificados.
No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of Seiko Epson Corporation. No
patent liability is assumed with respect to the use of the information contained herein. While every precaution has been taken in the preparation of this guide, Seiko Epson Corporation assumes no responsibility for errors or omissions. Neither is any
liability assumed for damages resulting from the use of the information contained herein.
Neither Seiko Epson Corporation nor its affiliates shall be liable to the purchaser of this product or third parties for damages, losses, costs, or expenses incurred by purchaser or third parties as a result of: accident, misuse, or abuse of this product or
unauthorized modifications, repairs, or alterations to this product, or (excluding the U.S.) failure to strictly comply with Seiko Epson Corporation's operating and maintenance instructions.
Seiko Epson Corporation shall not be liable against any damages or problems arising from the use of any options or any consumable products other than those designated as Original Epson Products or Epson Approved Products by Seiko Epson
Corporation.
EPSON is a registered trademark of Seiko Epson Corporation in Japan and other countries/regions.
NOTICE: The contents of this manual are subject to change without notice.
Copyright © 2013 Seiko Epson Corporation. All rights reserved.
Follow the instructions to install the optional DM-D110 on the TM-H6000IV-DT using the exclusive
DP-502 pole kit.
Suivez les instructions d'installation de l'afficheur DM-D110 en option sur l'imprimante
TM-H6000IV-DT en utilisant le kit tube DP-502 exclusif.
Siga las instrucciones para instalar la DM-D110 opcional en la TM-H6000IV-DT con el kit de tubo
exclusivo de la DP-502.
Siga as instruções para instalar a DM-D110 opcional na TM-H6000IV-DT utilizando o kit de pólo
exclusivo DP-502.
FR Déballage ES Desembalaje
EN Remove the two feet.
FR Retirez les deux pieds.
ES Extraiga las dos patas.
PT Remova as duas bases.
EN The illustration shows how to install the DM-D110 on the right side of the TM-H6000IV-DT. If
you install it on the left side, use screw hole L.
FR La figure montre comment installer l'afficheur DM-D110 à droite de l'imprimante TM-
H6000IV-DT. Si vous l'installez à gauche, utilisez un trou de vis en L.
ES La ilustración representa cómo instalar la DM-D110 en el lado derecho de la TM-H6000IV-DT.
Para instalarla en el lado izquierdo, utilice el agujero roscado L.
PT A ilustração mostra como instalar a DM-D110 no lado direito da TM-H6000IV-DT. Se instalá-la
no lado esquerdo, utilize o orifício para parafusos L.
PT Remoção da embalagem
Printed in Taiwan
412601700