General Power Tool Safety Warnings - Makita DTW284 Manual De Instrucciones

SAFETY WARNINGS

General power tool safety warnings

WARNING:
Read all safety warnings and
all instructions. F ailure to f ollo w t h e w arnings an d
instructions may result in electric shock, fire and/or
serious injury.
Save all warnings and instruc-
tions for future reference.
The term power tool in the warnings refers to your
mains-operate d ( c or d e d ) po w er tool or batter y -operate d
( c or d less ) po w er tool.
Cordless impact wrench safety
warnings
1 . Hold power tool by insulated gripping sur-
faces, when performing an operation where
the fastener may contact hidden wiring.
Fasteners contacting a live wire may make
exposed metal parts of the power tool live and
c oul d gi v e t h e operator an ele c tri c s h o c k.
2. Wear ear protectors.
3. Check the impact socket carefully for wear,
cracks or damage before installation.
old the tool firmly.
4 .
5 . Keep hands away from rotating parts.
Al ays be sure you have a firm footing.
6 .
Be sure no one is below when using the tool in
high locations.
7. The proper fastening torque may differ
depending upon the kind or size of the bolt.
Check the torque with a torque wrench.
SAVE THESE INSTRUCTIONS.
WARNING:
DO NOT let comfort or familiarity
with product ( gained from repeated use ) replace
strict adherence to safety rules for the subject
product.
MISUSE or failure to follow the safety rules stated
in this instruction manual may cause serious
personal injury.
Important safety instructions for
battery cartridge
1 . Before using battery cartridge, read all instruc-
tions and cautionary markings on ( 1 ) battery
charger, ( 2 ) battery, and ( 3 ) product using
battery.
2. Do not disassemble battery cartridge.
3. If operating time has become excessively
shorter, stop operating immediately. It may
result in a risk of overheating, possible burns
and even an explosion.
4 . If electrolyte gets into your eyes, rinse them
out with clear water and seek medical atten-
tion right away. It may result in loss of your
eyesight.
5 . Do not short the battery cartridge:
( 1 ) Do not touch the terminals with any con-
ductive material.
( 2 ) Avoid storing battery cartridge in a con-
tainer with other metal objects such as
nails, coins, etc.
( 3 ) Do not expose battery cartridge to water
or rain.
A battery short can cause a large current
o , overheating, possible burns and even a
breakdown.
6 . Do not store the tool and battery cartridge in
locations where the temperature may reach or
exceed 50 ° C ( 122 ° F ) .
7. Do not incinerate the battery cartridge even if
it is severely damaged or is completely worn
out. The battery cartridge can explode in a fire.
8 . Be careful not to drop or strike battery.
.
Do not use a damaged battery.
1 0. The contained lithium-ion batteries are subject
to the Dangerous Goods Legislation require-
ments.
F or c ommer c ial transports e.g. b y t h ir d parties,
f or w ar d ing agents, spe c ial re q uirement on pa c k-
aging an d labeling must be obser v e d .
F or preparation o f t h e item being s h ippe d , c onsult-
ing an expert for hazardous material is required.
Please also observe possibly more detailed
national regulations.
Tape or mask off open contacts and pack up the
batter y in su c h a manner t h at it c annot mo v e
aroun d in t h e pa c kaging.
1 1 . Follow your local regulations relating to dis-
posal of battery.
SAVE THESE INSTRUCTIONS.
CAUTION:
Only use genuine Makita batteries.
U se o f non-genuine Makita batteries, or batteries t h at
h a v e been altere d , ma y result in t h e batter y bursting
causing fires, personal injury and damage. It will
also v oi d t h e Makita w arrant y f or t h e Makita tool an d
c h arger.
Tips for maintaining maximum
battery life
1 . Charge the battery cartridge before completely
discharged. Always stop tool operation and
charge the battery cartridge when you notice
less tool power.
2. Never recharge a fully charged battery car-
tridge. Overcharging shortens the battery
service life.
3. Charge the battery cartridge with room tem-
perature at 10 ° C - 40 ° C ( 50 ° F - 104 ° F ) . Let
a hot battery cartridge cool down before
charging it.
4 . Charge the battery cartridge if you do not use
it for a long period ( more than six months ) .
5 ENGLISH