Intended Use - Makita DTWA070 Manual De Instrucciones

ENGLISH ( Original instructions)
SPECIFICATIONS
Model:
F astening c apac ities
Max imum f astening torq ue
T orq ue range
S q uare d riv e
No load speed ( R P M)
I mpac ts per minute
O v erall length
R ated v oltage
Net w eigh t
Due to our continuing program of research and development, the specifications herein are subject to change
w it h out noti c e.
Specifications may differ from country to country.
• T h e w eig h t ma y d i f f er d epen d ing on t h e atta c h ment ( s ) , in c lu d ing t h e batter y c artri d ge. T h e lig h test an d h ea v i-
est c ombination, a c c or d ing to E P T A - P ro c e d ure 0 1 / 20 1 4 , are s h o w n in t h e table.
Applicable battery cartridge and charger
Battery c artrid ge
C h arger
• S ome o f t h e batter y c artri d ges an d c h argers liste d abo v e ma y not be a v ailable d epen d ing on y our region o f
resi d en c e.
WARNING:
Only use the battery cartridges and chargers listed above. U se o f an y ot h er batter y c artri d ges
and chargers may cause injury and/or fire.

Intended use

T h e tool is inten d e d f or f astening bolts an d nuts.
Noise
T h e t y pi c al A - w eig h te d noise le v el d etermine d a c c or d -
ing to EN 6 2 8 4 1 -2-2 :
Model DTWA070
S oun d pressure le v el ( L
S oun d po w er le v el ( L ) : 1 03 d B ( A )
W A
U n c ertaint y ( K ) : 3 d B ( A )
Model DTWA100
S oun d pressure le v el ( L
S oun d po w er le v el ( L ) : 1 0 4 d B ( A )
W A
U n c ertaint y ( K ) : 3 d B ( A )
Model DTWA140
S oun d pressure le v el ( L
S oun d po w er le v el ( L ) : 1 07 d B ( A )
W A
U n c ertaint y ( K ) : 3 d B ( A )
Model DTWA190
S oun d pressure le v el ( L
S oun d po w er le v el ( L ) : 1 0 6 d B ( A )
W A
U n c ertaint y ( K ) : 3 d B ( A )
S tand ard bolt
H igh tensile bolt
) : 9 2 d B ( A )
pA
) : 9 3 d B ( A )
pA
) : 9 6 d B ( A )
pA
) : 9 5 d B ( A )
pA
DTWA070 DTWA100
M5 - M1 2
M5 - M1 0
6 5 N• m 9 5 N• m
A pprox . A pprox .
5 - 4 0 N• m 6 - 6 5 N• m
9 .5 mm
-1
0 - 2,5 00 min
-1
0 - 3,700 min
1 4 4 mm 1 5 1 mm
1 .1 - 1 .4 kg 1 .2 - 1 .4 kg
BL 1 4 1 5 N / BL 1 4 1 5 NA / BL 1 4 30 / BL 1 4 30B / BL 1 4 4 0 / BL 1 4 5 0 /
BL 1 4 6 0A / BL 1 4 6 0B
D C 1 8 R C / D C 1 8 R D / D C 1 8 R E / D C 1 8 S D / D C 1 8 S E / D C 1 8 S F /
NOTE: T h e d e c lare d noise emission v alue ( s ) h as
been measure d in a c c or d an c e w it h a stan d ar d test
met h o d an d ma y be use d f or c omparing one tool w it h
anot h er.
NOTE: T h e d e c lare d noise emission v alue ( s )
ma y also be use d in a preliminar y assessment o f
e x posure.
WARNING:
Wear ear protection.
WARNING:
The noise emission during actual
use of the power tool can differ from the declared
value ( s ) depending on the ways in which the
tool is used especially what kind of workpiece is
processed.
WARNING:
Be sure to identify safety mea-
sures to protect the operator that are based on an
estimation of exposure in the actual conditions of
use ( taking account of all parts of the operating
cycle such as the times when the tool is switched
off and when it is running idle in addition to the
trigger time ) .
5 ENGLISH
DTWA140
M6 - M1 6
M6 - M1 2
1 4 0 N• m
A pprox .
1 8 - 8 0 N• m 25 - 1 25 N• m
1 2.7 mm
-1
0 - 2,700 min 0 - 2,6 00 min
-1
0 - 3,300 min 0 - 3,000 min
1 5 8 mm
D .C . 1 4 .4 V
1 .2 - 1 .5 kg 1 .3 - 1 .6 kg
D C 1 8 S H
DTWA190
M8 - M1 6
M8 - M1 4
1 8 5 N• m
A pprox .
-1
-1