Makita DVC152L Manual De Instrucciones página 15

Connecting the hose
NOTICE:
Never force the hose for bending or stamp it.
Never move the cleaner by a hose. F orc ing, stamping and pull-
ing th e h ose may c ause a breakage or d ef ormation of th e h ose.
NOTICE:
W hen picking up large wastes such as planer
carvings, concrete dusts or similar other than small
wastes, use the 38 mm inner diameter hose (optional
accessory ) . U sing t h e 2 8 mm inner d iameter h ose ( optional
accessory) may cause a hose stuffing and damage.
I nsert t h e h ose onto t h e mounting port o f t h e tank an d
turn it c lo c k w ise until it lo c ks.
Fig.21
W IRELESS ACTIVATION
FUNCTION
For DVC154L only
W hat you can do with the wireless
activation function
T h e w ireless a c ti v ation f un c tion enables c lean an d
c om f ortable operation. B y c onne c ting a supporte d tool
to t h e c leaner, y ou c an run t h e c leaner automati c all y
along w it h t h e s w it c h operation o f t h e tool.
Fig.22
NOTICE:
Be sure to refer to the instruction manual of the
tool when using the cleaner with wireless activation function.
NOTICE:
Do not disassemble or tamper with the
wireless unit.
NOTICE:
Always close the lid of the wireless unit
in the tool when operating or storage.
NOTICE:
Do not remove the wireless unit from the
tool while the power is being supplied to the tool.
D oing so ma y c ause a mal f un c tion o f t h e w ireless unit.
NOTICE:
Do not press the wireless activation button too
hard and/or press the button with an object with a sharp edge.
NOTE: W ireless a c ti v ation nee d s Makita tools
e q uippe d w it h t h e w ireless unit.
NOTE: P rior to t h e initial use o f t h e w ireless a c ti v ation
f un c tion w it h ea c h tool, t h e tool registration is re q uire d .
Once the registration is finished with the tool, the
re-registration is not re q uire d unless it is c an c elle d .
NOTE: Be f ore registration, be sure t h at t h e w ireless
unit is properl y inserte d into t h e tool.
NOTE: O ne c leaner c an register up to 1 0 tools. I f
more t h an 1 0 tools are registere d to t h e c leaner, t h e
tool registere d earliest w ill be c an c elle d automati c all y .
NOTE: T h e position o f t h e w ireless a c ti v ation button
v aries d epen d ing on t h e tool.
NOTE: T h e c leaner also starts b y pressing t h e po w er
button w h en t h e stan d -b y s w it c h is set to " A U T O " .
H o w e v er t h e po w er button w ill not a c tuate w h en t h e
w ireless a c ti v ation f un c tion is use d .
Tool registration for the cleaner
NOTE: A Makita tool supporting t h e w ireless a c ti v a-
tion f un c tion is re q uire d f or t h e tool registration.
NOTE: F inis h installing t h e w ireless unit to t h e tool
be f ore starting t h e tool registration.
NOTE: D uring t h e tool registration, d o not pull t h e
s w it c h trigger on t h e tool or turn on t h e po w er s w it c h
on t h e c leaner.
NOTE: R e f er to t h e instru c tion manual o f t h e tool, too.
I f y ou w ish to ac tiv ate th e c leaner along w ith th e sw itc h
operation of the tool, finish the tool registration beforehand.
1. I nstall t h e batteries to t h e c leaner an d t h e tool.
2. S et t h e stan d -b y s w it c h on t h e c leaner to " A U T O " .
Fig.23: 1. S tan d -b y s w it c h
3. P ress t h e w ireless a c ti v ation button on t h e c leaner
f or 3 se c on d s until t h e w ireless a c ti v ation lamp blinks in
green. A n d t h en press t h e w ireless a c ti v ation button on
t h e tool in t h e same w a y .
Fig.24: 1. W ireless a c ti v ation button 2. W ireless
a c ti v ation lamp
I f t h e c leaner an d t h e tool are linke d su c c ess f ull y , t h e
w ireless a c ti v ation lamps w ill lig h t up in green f or 2
se c on d s an d start blinking in blue.
NOTE: The wireless activation lamps finish blinking
in green a f ter 20 se c on d s elapse d . P ress t h e w ireless
a c ti v ation button on t h e tool w h ile t h e w ireless a c ti-
v ation lamp on t h e c leaner is blinking. I f t h e w ireless
a c ti v ation lamp d oes not blink in green, pus h t h e w ire-
less activation button briefly and hold it down again.
NOTE: W h en per f orming t w o or more tool registration
for the cleaner, finish the tool registration one by one.
Starting the wireless activation function
NOTE: F inis h t h e tool registration f or t h e c leaner f or
w ireless a c ti v ation.
NOTE: A l w a y s pla c e t h e c leaner so t h at y ou c an see
t h e status o f t h e w ireless a c ti v ation lamp.
NOTE: R e f er to t h e instru c tion manual o f t h e tool, too.
A f ter registering a tool to t h e c leaner, t h e c leaner w ill
automati c all y runs along w it h t h e s w it c h operation o f
t h e tool.
1. I nstall t h e w ireless unit to t h e tool.
2. C onne c t t h e h ose o f t h e c leaner w it h t h e tool.
Fig.25
3. S et t h e stan d -b y s w it c h on t h e c leaner to " A U T O " .
Fig.26: 1. S tan d -b y s w it c h
4. P us h t h e w ireless a c ti v ation button on t h e tool
briefly. The wireless activation lamp will blink in blue.
Fig.27: 1. W ireless a c ti v ation button 2. W ireless
a c ti v ation lamp
5. P ull th e sw itc h trigger of th e tool. C h ec k if th e c leaner
runs w h ile th e sw itc h trigger on th e tool is being pulled .
T o stop t h e w ireless a c ti v ation, pus h t h e w ireless a c ti v a-
tion button on t h e tool, or set t h e stan d -b y s w it c h on t h e
c leaner to " I " or " O " .
15 ENGLISH