Makita DVC265 Manual De Instrucciones página 13

Indicating the remaining battery
capacity
Only for battery cartridges with the indicator
Fig.2: 1. I n d i c ator lamps 2. C h e c k button
P ress t h e c h e c k button on t h e batter y c artri d ge to in d i-
c ate t h e remaining batter y c apa c it y . T h e in d i c ator lamps
lig h t up f or a f e w se c on d s.
Indicator lamps
Lighted Off
NOTE: D epen d ing on t h e c on d itions o f use an d t h e
ambient temperature, t h e in d i c ation ma y d i f f er slig h tl y
f rom t h e a c tual c apa c it y .
Switch box position
T h e s w it c h bo x c an be h ooke d on eit h er si d e o f t h e
lo w er belt. A rrange t h e c or d so t h at t h e s w it c h bo x
c omes to y our d esire d si d e. T o pre v ent t h e c or d f rom
being d amage d , pass t h e c or d t h roug h t h e h ook as
illustrate d .
Fig.3: 1. H ook 2. C or d
Adjusting belts
T h e tig h tness o f t h e s h oul d er belts, upper an d lo w er
belts can be adjusted. Put your arms through the shoul-
der belts first then fasten the lower and upper belts.
T o tig h ten, pull t h e en d o f t h e strap as illustrate d . T o
loosen, pull up t h e en d o f t h e f astener.
Lower belt
Fig.4: 1. S trap 2. F astener
Shoulder belts
Fig.5: 1. S trap 2. F astener
Upper belt
Fig.6: 1. S trap 2. F astener
Carrying hook
A l w a y s grab t h e c arr y ing h ook w h en h an d ling t h e v a c -
uum c leaner bo d y .
Fig.7: 1. C arr y ing h ook
Remaining
capacity
Blinking
75 % to 1 00%
5 0% to 75 %
25 % to 5 0%
0% to 25 %
C h arge th e
battery .
T h e battery
may h av e
mal f un c tione d .
13 ENGLISH
Stand-by switch
T h e stan d -b y s w it c h is t h e s w it c h to turn on / o f f t h e
w ireless a c ti v ation f un c tion. T h e v a c uum c leaner is in
t h e stan d -b y state regar d less o f t h e s w it c h position an d
it runs w h en button is pus h e d .
Fig. 8 : 1. S tan d -b y s w it c h
Switch position
A U T O I T h e v ac uum c leaner is in th e stand -by
( O N) state and th e w ireless ac tiv ation f unc tion
is av ailable.
O T h e v ac uum c leaner is in th e stand -by
( O F F ) state h ow ev er th e w ireless ac tiv ation
f unc tion is not av ailable.
Switch action
T o start v a c uuming, press
c leaner w ill start in t h e same su c tion po w er w h en y ou
turne d it o f f pre v iousl y . W h en y ou press
w h ile t h e v a c uum c leaner is running, t h e su c tion po w er
s w it c h es bet w een normal ( 1 ) an d h ig h er ( 2 ) su c tion
po w er. T o turn o f f t h e v a c uum c leaner, press
Fig.9
NOTE: I f y ou w ant to run t h e v a c uum c leaner along
w it h t h e s w it c h operation o f t h e tool c onne c te d to t h e
v a c uum c leaner ( w ireless a c ti v ation f un c tion ) , set t h e
stan d -b y s w it c h to " I ( O N ) " .
NOTE: To use the wireless activation function, finish
t h e tool registration be f ore h an d . R e f er to " W I R E L E S S
A C T I V A T I O N F U N C T I O N " se c tion f or d etail.
NOTE: W h en using t h e w ireless a c ti v ation f un c -
tion, y ou w ill not be able to stop t h e v a c uuming
b y button.
Hose band
H ose ban d c an be use d f or h ol d ing t h e h ose or f ree
no z z le.
T o se c ure t h e h ose to t h e v a c uum c leaner bo d y , pass
t h e h ose ban d t h roug h t h e slot on t h e bo d y . Y ou c an
atta c h t h e h ose ban d on eit h er si d e.
Fig.10: 1. H ose ban d 2. S lot 3. H ose
ASSEMBLY
CAUTION:
Always be sure that the tool is
switched off and the battery cartridge is removed
before carrying out any work on the tool.
Assembling hose
I nsert t h e h ose c u f f into t h e v a c uum c leaner bo d y an d
turn it c lo c k w ise.
Fig.11: 1. H ose c u f f 2. Va c uum c leaner bo d y
Status
button on c e. T h e v a c uum
button
button.