Makita DVC265 Manual De Instrucciones página 16

Installing the wireless unit
Place the cleaner on a at and
CAUTION:
stable surface when installing the wireless unit.
NOTICE:
Clean the dust and dirt on the cleaner
before installing the wireless unit. D ust or d irt ma y c ause
mal f un c tion i f it c omes into t h e slot o f t h e w ireless unit.
NOTICE:
To prevent the malfunction caused by
static, touch a static discharging material, such as
a metallic part, before picking up the wireless unit.
NOTICE:
W hen installing the wireless unit, always
be sure that the wireless unit is inserted in the cor-
rect direction and the lid is completely closed.
Open the lid on the cleaner as shown in the figure.
1.
Fig.32: 1. L i d
2. I nsert t h e w ireless unit to t h e slot an d t h en c lose t h e li d .
When inserting the wireless unit, align the projections
w it h t h e re c esse d portions on t h e slot.
Fig.33: 1. W ireless unit 2. Projection 3. L i d
4. R e c esse d portion
W h en remo v ing t h e w ireless unit, open t h e li d slo w l y .
T h e h ooks on t h e ba c k o f t h e li d w ill li f t t h e w ireless unit
as y ou pull up t h e li d .
Fig.34: 1. W ireless unit 2. H ook 3. L i d
A f ter remo v ing t h e w ireless unit, keep it in t h e supplie d
c ase or a stati c - f ree c ontainer.
NOTICE:
Always use the hooks on the back of
the lid when removing the wireless unit. I f t h e
h ooks d o not c at c h t h e w ireless unit, c lose t h e li d
c ompletel y an d open it slo w l y again.
Tool registration for the cleaner
NOTE: A Makita tool supporting t h e w ireless a c ti v a-
tion f un c tion is re q uire d f or t h e tool registration.
NOTE: F inis h installing t h e w ireless unit to t h e tool
be f ore starting t h e tool registration.
NOTE: D uring t h e tool registration, d o not pull t h e s w it c h
trigger on t h e tool or pus h t h e c leaner ' s s w it c h f or v a c uuming.
NOTE: R e f er to t h e instru c tion manual o f t h e tool, too.
I f y ou w ish to ac tiv ate th e c leaner along w ith th e sw itc h
operation of the tool, finish the tool registration beforehand.
1. I nstall t h e w ireless units to t h e c leaner an d t h e
tool, respe c ti v el y .
2. I nstall t h e batteries to t h e c leaner an d t h e tool.
3. S et t h e stan d -b y s w it c h on t h e c leaner to " I ( O N ) " .
Fig.35: 1. S tan d -b y s w it c h
4. P ress t h e w ireless a c ti v ation button on t h e c leaner
f or 3 se c on d s until t h e w ireless a c ti v ation lamp blinks in
green. A n d t h en press t h e w ireless a c ti v ation button on
t h e tool in t h e same w a y .
Fig.36: 1. W ireless a c ti v ation button 2. W ireless
a c ti v ation lamp
I f t h e c leaner an d t h e tool are linke d su c c ess f ull y , t h e
w ireless a c ti v ation lamps w ill lig h t up in green f or 2
se c on d s an d start blinking in blue.
NOTE: The wireless activation lamps finish blinking
in green a f ter 20 se c on d s elapse d . P ress t h e w ireless
a c ti v ation button on t h e tool w h ile t h e w ireless a c ti-
v ation lamp on t h e c leaner is blinking. I f t h e w ireless
a c ti v ation lamp d oes not blink in green, pus h t h e w ire-
less activation button briefly and hold it down again.
NOTE: W h en per f orming t w o or more tool registration
for the cleaner, finish the tool registration one by one.
Starting the wireless activation
function
NOTE: F inis h t h e tool registration f or t h e c leaner f or
w ireless a c ti v ation.
NOTE: A l w a y s pla c e t h e c leaner so t h at y ou c an see
t h e status o f t h e w ireless a c ti v ation lamp.
NOTE: R e f er to t h e instru c tion manual o f t h e tool, too.
A f ter registering a tool to t h e c leaner, t h e c leaner w ill
automati c all y runs along w it h t h e s w it c h operation o f
t h e tool.
1. I nstall t h e w ireless units to t h e c leaner an d t h e
tool, respe c ti v el y .
2. I nstall t h e batteries to t h e c leaner an d t h e tool.
3. C onne c t t h e h ose o f t h e c leaner w it h t h e tool.
Fig.37
4. S et t h e stan d -b y s w it c h on t h e c leaner to " I ( O N ) " .
T h e w ireless a c ti v ation lamp w ill blink in blue.
Fig.3 8 : 1. S tan d -b y s w it c h
5. P us h t h e w ireless a c ti v ation button on t h e tool
briefly. The wireless activation lamp will blink in blue.
Fig.39: 1. W ireless a c ti v ation button 2. W ireless
a c ti v ation lamp
6. P ull t h e s w it c h trigger o f t h e tool. C h e c k i f t h e
c leaner runs w h ile t h e s w it c h trigger on t h e tool is being
pulle d .
CAUTION:
Always check if the wireless acti-
vation function works before starting a work with
the tool.
T o stop t h e w ireless a c ti v ation, pus h t h e w ireless a c ti v a-
tion button on t h e tool or set t h e stan d -b y s w it c h on t h e
c leaner to " O ( O F F ) " .
NOTE: T h e w ireless a c ti v ation lamp on t h e tool w ill
stop blinking in blue w h en t h ere is no operation f or
2 h ours. I n t h is c ase, press t h e w ireless a c ti v ation
buttons on t h e tool again.
NOTE: T h e c leaner starts / stops w it h a d ela y . T h ere is
a time lag w h en t h e c leaner d ete c ts a s w it c h opera-
tion o f t h e tool.
NOTE: T h e transmission d istan c e o f t h e w ireless unit
ma y v ar y d epen d ing on t h e lo c ation an d surroun d ing
c ir c umstan c es.
NOTE: W h en t w o or more tools are registere d to one
c leaner, t h e c leaner ma y start running e v en i f y ou
d on ' t pull t h e s w it c h trigger be c ause ot h er user is
using t h e w ireless a c ti v ation f un c tion.
16 ENGLISH