Bosch 5312 Instrucciones De Funcionamiento Y Seguridad página 3

Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

conditions. Everyday eyeglasses only have
impact resistant lenses, they are NOT safety
glasses.
Tool Use and Care
• Use clamps or other practical way to secure
and support the wotkpiece to a stable plat-
form. Holding the work by hand or against your
body is unstable. Itallows for work to shift, causes
binding of the tool and loss of control.
• Do not force tool. Use the correct tool for your
application.
The correct tool will do the job better
and safer at the rate for which it is designed. Do
not use the tool for purpose not intended - for ex-
ample; do not use the miter saw for slicing meats.
• Do not use tool if switch does not turn it "ON"
or "OFF". Any tool that cannot be controlled with
the switch is dangerous.
• Disconnect the plug from the power source
before making any adjustments
or changing
accessories.
Such preventive safety measures
reduce the risk of starting the tool accidentally.
• Keep cutting tools sharp and clean. Properly
maintained tools, with sharp cutting edges, are
less likely to bind and easier to control. When
mounting saw blades be certain that the arrow on
thblade matches the direction of the arrow marked
on the tool and that the teeth are also pointing in
the same direction.
• Inspect
guards
before
using
a tool.
Keep
guards
in place. Check moving
parts for bind-
ing or any other condition
that may affect the
normal
operation
or safety features
of the tool.
If damaged,
have tool serviced
before
using
the tool.
Many accidents
are caused
by poorly
maintained
tools.
• Do not alter or misuse tool. Any alteration or
modification is a misuse and may result in serious
personal injury.
• The use of any other accessories
not speci-
fied in this manual may create a hazard. Ac-
cessories that may be suitable for one type of tool,
may become hazardous when used on an inap-
propriate tool.
Service
• Tool service must be performed only by qual-
ified repair personnel. Service or maintenance
performed by unqualified personnel may result in
misplacing internal wires and components which
could cause serious hazard.
When servicing
a tool,
use only identical
re-
placement
parts.
Follow
instructions
in the
Maintenance
section
of this manual.
Use of
unauthorized
parts or failure to follow Maintenance
Instructions
may create a hazard.
Safety Rules For Miter Saws
• Use clamps
to support
wotkpiece
whenever
possible,
if supporting
the workpiece
by hand,
you must
always
keep
hand
outside
of "No
Hand"
area as marked
with a symbol
on the
base.
Do not use this saw to cut pieces
that
are too small
to be securely
clamped.
Your
hand
if
placed
inside
the
"No
Hands"
region can easily slip or be pulled into the blade.
• Do not reach in back of the saw blade behind
the fence with either hand to hold
down or support
the workpiece,
remove
wood
scraps,
or for any other reason.
The proximity
of the spinning saw blade to your hand may not
be obvious and you may be seriously
injured.
• Never cross your
hand
over intended
line of
cutting.
Supporting the workpiece
"cross handed"
i.e. holding the left side of the workpiece
with your
right hand is very dangerous.
• Always
disconnect
the power cord
from
the
power source
before making
any adjustments
or attaching
any accessories.
You may unin-
tentionally
start the saw, leading
to serious
per-
sonal injury.
• Miter saws are intended to cut wood or wood-
like products, they cannot
be used with abra-
sive cutoff
wheels for cutting
ferrous
material
such as bars, rods, studs, etc.
However,
if cut-
ting materials
like aluminum
or other non-fer-
rous metals,
use only saw blades
specifically
recommended
for non ferrous
metal
cutting.
Cutting ferrous materials causes excessive spark-
ing and will damage the lower guard and will over-
load the motor.
(NOTE: Robert Bosch Tool Corporation does not
offer 12" metal cutting blades.)
Inspect your workpiece
before cutting.
If
wotkpiece is bowed or warped, clamp it with
the outside bowed face toward the fence. Al-
ways make certain that there is no gap be-
tween the workpiece,
fence and table along
the line of the cut. Bent or warped workpieces
can twist or rock and may cause binding on the
spinning saw blade while cutting. Also, make sure
there are no nails or foreign objects in the work-
piece.
"SAVE THESE INSTRUCTIONS"
-3-

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

5412

Tabla de contenido